Yaesu FT-897D - CAT (Computer Aided Transceiver) Operation; CAT Data Protocol; Constructing and Sending CAT Commands

Page 61FT-897D OPERATING MANUAL
MENU MODE No•061
[
MTR ATX SEL
]
Function: Selects the meter display configuration while the
transceiver is transmitting.
Available Values: PWR, ALC, MOD, SWR, VLT, N/A, OFF
Default: PWR
PWR: Indicates the relative transmit power.
ALC: Indicates the relative Automatic Level Control voltage.
MOD: Indicates the deviation level.
SWR: Indicates the Standing Wave Ratio
(forward:reflected).
VLT: Indicates the battery voltage.
N/A: Not available at this time.
OFF: Disables the meter.
MENU MODE No-062
[
MTR PEAK HOLD
]
Function: Enabling/disabling of the “peak hold” function
of the meter.
Available Values: OFF/ON
Default: ON
MENU MODE No- 063
[
NB LEVEL
]
Function: Setting of the blanking level for the IF Noise
Blanker.
Available Values: 0 ~ 100
Default: 50
MENU MODE No•064
[
OP FILTER 1
]
Not available at this time.
MENU MODE No•065
[
PG A
]
Function: Programming the
[
A
]
key (in the Operating Func-
tion Row 17) function.
Available Values: All Multi Function , all Menu Item,
MONI, Q.SPL, TCALL, ATC and USER.
Default: MONI
MENU MODE No • 066
[
PG B
]
Function: Programming the
[
B
]
key (in the Operating Func-
tion Row 17) function.
Available Values: All Multi Function , all Menu Item,
MONI, Q.SPL, TCALL, ATC and USER.
Default: Q.SPL
MENU MODE No•067
[
PG C
]
Function: Programming the
[
C
]
key (in the Operating Func-
tion Row 17) function.
Available Values: All Multi Function , all Menu Item,
MONI, Q.SPL, TCALL, ATC and USER.
Default: ATC
MENU MODE No•068
[
PG ACC
]
Function: Programming the optional MH-59A8J
microphone’s
[
ACC
]
button assignment.
Available Values: All Multi Functions, all Menu Items (ex-
cept Menu #065 through 070), MONI, Q.SPL, TCALL, ATC
and USER.
Default: MONI
MENU MODE No •069
[
PG P1
]
Function: Programming the optional MH-59A8J
microphone’s
[
P1
]
button assignment.
Available Values: All Multi Functions, all Menu Items (ex-
cept Menu #065 through 070), MONI, Q.SPL, TCALL, ATC
and USER.
Default: Q.SPL
MENU MODE No•070
[
PG P2
]
Function: Programming the optional MH-59A8J
microphone’s
[
P2
]
button assignment.
Available Values: All Multi Functions, all Menu Items (ex-
cept Menu #065 through 070), MONI, Q.SPL, TCALL, ATC
and USER.
Default: TCALL
MENU MODE No•071
[
PKT1200
]
Function: Adjusts the audio input level from the TNC dur-
ing 1200 bps Packet operation.
Available Values: 0 ~ 100
Default: 50
MENU MODE No•072
[
PKT9600
]
Function: Adjusts the audio input level from the TNC dur-
ing 9600 bps Packet operation.
Available Values: 0 ~ 100
Default: 50
MENU MODE No•073
[
PKT RATE
]
Function: Sets the transceiver’s circuitry for the Packet baud
rate to be used.
Available Values: 1200/9600 (bps)
Default: 1200 (bps)
MENU MODE No- 074
[
PROC LEVEL
]
Function: Sets the compression level for the AF speech pro-
cessor in the SSB/AM modes.
Available Values: 0 ~ 100
Default: 50
MENU MODE No-075
[
RF POWER SET
]
Function: Setting of the maximum power level for the cur-
rent band.
Available Values: 5 ~ 100
Default: 100
MENU MODE No-076
[
RPT SHIFT
]
Function: Sets the magnitude of the repeater shift.
Available Values: 0.00 ~ 99.99 (MHz)
Default: Depends on operating band and transceiver ver-
sion.
MENU OPERATION