Yakima HoldUp - User Manual

1034426J-1/21
HoldUp
SAFETY CLIP (1X)
WRENCH (1X)
REAR WHEEL TRAY
ASSEMBLY (1X)
FRONT WHEEL TRAY
ASSEMBLY (1X)
HITCH BOLT (1X)
1 1/4" BASE (1X)
(1 1/4" HOLDUP ONLY)
2" BASE (1X)
(2" HOLDUP ONLY)
LOCK WASHER (1X)
KEY (2X)
HEX WRENCH (1X)
HITCHLOCK (1X)
For Your
Safety
Warranty
Registration
on-line
YAKIMA.com
 Install This product on 2" OR 1¼" hitch
receivers ONLY.
 Do not use with hitch-extenders or with
1 ¼” hitch adapters.
 Do not install on trailers, campers, or RVs.
 Do not install if spare tire causes
interference with bikes, or folded carrier.
 Not for use on bikes with front fenders.
In addition, some undersized receivers may
not accept this product. If you do not know the
capabilities of your hitch receiver, consult an
automotive professional.
IMPORTANT WARNING
IT IS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY ATTACHED TO YOUR VEHICLE. IMPROPER
ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR
TO OTHERS. YOU ARE RESPONSIBLE FOR SECURING THE RACKS AND ACCESSORIES TO YOUR CAR, CHECKING THE ATTACHMENTS
PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU
MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS SUPPLIED WITH YOUR YAKIMA PRODUCT PRIOR TO INSTALLATION
OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT
THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER.

Summary

YAKIMA HoldUp Product Overview and Safety

Installation Compatibility Requirements

Specifies hitch receiver size, adapter usage, trailer compatibility, and tire interference for installation.

Included Components and Tools

Lists and illustrates all parts and tools included with the HoldUp bike rack for assembly.

Critical Safety and Warranty Information

Highlights essential safety warnings for attachment and potential hazards, plus warranty registration details.

YAKIMA HoldUp Installation Procedure

Hitch Mount Installation Steps

Guides on inserting the base into the hitch receiver, fastening the hitch bolt, and positioning the base.

Attaching Wheel Trays to Base

Instructions for attaching the lower and upper wheel trays to the hitch base, noting correct orientation.

Loading the First Bike

Steps for folding the rack down, preparing trays, and loading the heaviest bike first securely.

Securing Bike and Loading Second Bike

Securing the first bike's wheel hook and strap, and instructions for loading a second bike if applicable.

Final Security and Pre-Drive Checks

Using the integrated locking cable, performing final installation checks, and reviewing additional warnings.

YAKIMA HoldUp Usage, Maintenance, and Support

Load Limits and Bike Restrictions

Specifies maximum load per bike and lists types of bikes or accessories that should not be transported.

Maintenance and Care Instructions

Guidance on periodic lubrication, cleaning of parts, and pre-wash rack removal.

Technical Assistance and Warranty Details

Contact information for support, replacement parts, and details about the product's limited lifetime warranty.

Yakima HoldUp Specifications

General

Bike Capacity	2 bikes
Weight Capacity	60 lbs per bike
Foldable	Yes
Locking System	Integrated cable lock and hitch lock
Material	Steel
Tilt Feature	Yes
Type	Hitch Bike Rack
Hitch Receiver Size	1.25 inches or 2 inches
Wheel Size Compatibility	20" to 29"
Max Tire Width	5"
Security Features	Integrated cable lock, hitch lock receiver