Yale 5300LN Grade 2

3. Install latch.
Insert latch in door. (Be sure bevel
edge of bolt faces strike plate.)
Attach with two screws supplied.
2. Drill door.
A. Drill 2-1/8" (54mm) dia. hole thru
the door. Cut notches as shown on
template. See note. (Except
Dummy Trim)
B. Drill 1" (26mm) dia. hole in edge of
door. Mortise for latch front 1-1/8"
(29mm) wide x 2-1/4" (57mm) high
x 5/32" (4mm) deep. (Except
Dummy Trim)
C. Drill two (2) 5/16" (8mm) dia.
holes thru door. See note.
D. Drill pilot holes for latch
screws. 7/64" (2.5mm) dia.
(Except Dummy Trim)
Note: To avoid splintering wood
doors, drill holes (A) and (C) from
both sides of the door.
D
B
1. Mark door.
Mark horizontal line across edge of
door for centerline of lock at desired
installation height. Fold template over
edge of door, centering on horizontal
line. Mark centers of holes at proper
backset.
For beveled and square edge doors,
mark both sides of the door.
Note:
Be sure to verify backset before
marking & drilling door.
5300LN Grade 2 or 4700LN Grade 1
Cylindrical Lever Locksets
Installation Instructions
Door
Marker
4. Unpack lock.
Attention Installer
Installation of cylindrical locks and latches must be through
bolted in all doors. If installation instructions are not followed this
may result in damage to the lock and void the factory warranty.
Any retrofit or other field modification to a fire rated opening can
potentially impact the fire rating of the opening, and Yale Locks &
Hardware makes no representations or warranties concerning
what such impact may be in any specific situation. When
retrofitting any portion of an existing fire rated opening, or
specifying and installing a new fire-rated opening, please consult
with a code specialist or local code official (Authority Having
Jurisdiction) to ensure compliance with all applicable codes and
ratings.
Tools Required
• 2-1/8" (54mm) hole saw
• 1" (26mm) boring bit
• 5/16" (8mm) drill bit
• 7/64" (2.5mm) drill bit
• Chisel & hammer
• #2 phillips screw driver
• Handle removal tool (supplied)
• 3/8" or 1/2" drill
IMPORTANT: The accuracy of the door preparation is
critical for the proper functioning and security of this lever
handle lock. Misalignment can cause premature wear and
tear and a lessening of security.
Outside Assembly
(stays assembled)
Bushing
Inside Rose
Support Assembly
Through Bolts
Inside Lever
Handle
An ASSA ABLOY Group brand
80-9150-0060-010 (11-16)

Yale 5300LN Grade 2 Specifications

General

Series	5300LN
Grade	2
Keyway	Yale
Handing	Reversible
Backset	2-3/4 inches
Door Thickness	1-3/8" to 1-3/4"
Latchbolt Throw	1/2 inch
Deadbolt Throw	1 inch
Material	Steel
ANSI/BHMA Certification	Grade 2
Finish	Various (e.g., Satin Nickel, Oil Rubbed Bronze)

Summary

Important Safety and Installation Notes

IMPORTANT

Accuracy of door preparation is critical for proper functioning, security, and to prevent premature wear.

Attention Installer

Follow instructions to avoid damage, voiding warranty, and ensure compliance with fire ratings and codes.

Tools and Preparation

Tools Required

List of tools needed for installation, including drill bits, hole saws, and screwdrivers.

Mark door

Mark horizontal line for lock centerline and centers of holes at proper backset.

Drill door

Drill holes for lockset and latch, including mortising for the latch front.

Install latch

Insert latch into door with bevel facing strike plate and secure with screws.

Unpack lock

Unpack the lockset components carefully.

Lockset Assembly and Installation

Adjust lock for door thickness

Adjust rose plate for 1-3/4" or 2-1/4" door thickness.

Install lock

Insert lockbody into door, ensuring hooks engage latch case and retractor engages bolt tail.

Install inside components

Slide rose support, install bushing, align rose scalp, and install lever handle.

Strike installation (Wood Frames Only)

Mark, drill, and mortise door frame for strike plate installation.

TEST THE OPERATION OF THE LOCKSET

Cycle lock to test smooth operation when door is open and closed.

Troubleshooting and Specialized Functions

Troubleshooting

Addresses issues like door binding, latchbolt not deadlocking, or latchbolt not retracting.

TO REMOVE CYLINDER HANDLE

Procedure to remove the cylinder handle using a retainer tool.

DUMMY TRIM INSTALLATION

Instructions for installing dummy trim, securing rose support and rose scalp.

TO REPLACE OR INSTALL CYLINDER

Steps to remove sleeve, slide cylinder into sleeve, and install handle.

Adjust for Door Thickness

Specific instructions for adjusting door thickness for 5328LN, 5329LN, etc.

Finish Care

Guidelines for cleaning and maintaining the lockset's finish to ensure longevity.