EasyManuals Logo

Yamaha RX-V477 Easy Setup Guide

Yamaha RX-V477
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
АВ ресивер/AV Receiver
Руководство по быстрой настройке/Easy Setup Guide
Русский
English
В этом документе объясняется, как настроить 5.1-канальную систему и воспроизвести на аппарате
объемный звук с BD/DVD-диска.
Дополнительные сведения об этом продукте см. в “Инструкции по эксплуатации” на компакт-диске,
входящем в комплект поставки.
Последнюю редакцию “Инструкции по эксплуатации” можно загрузить со следующего веб-сайта:
http://download.yamaha.com/
This document explains how to set up a 5.1-channel system and play back surround sound from a BD/DVD on
the unit.
For more information about this product, refer to the Owner’s Manual included on the supplied CD-ROM.
The latest Owner’s Manual can be downloaded from the following website.
http://download.yamaha.com/
© 2014 Yamaha Corporation Printed in China ZK44440-1
F
HDMI HDMI
HDMI
HDMI
HDMI HDMI
HDMI
HDMI HDMI
1 2 3 4
1 2 3 4
5
4
21
3
9
1
2
1
Accessories used with this
document
1
Remote control
2
Batteries (AAA, R03, UM-4) (x2)
3
YPAO microphone
The following cables (not supplied) are required to build the
system described in this document.
Speaker cables (x5)
Audio pin cable (x1)
HDMI cables (x3)
2
Placing speakers
Set up the speakers in the room using the diagram as a
reference.
1 Front speaker (L)
2 Front speaker (R)
3 Center speaker
4 Surround speaker (L)
5 Surround speaker (R)
9 Subwoofer
3
Connecting speakers/subwoofer
U.S.A. and Canada models only
When connecting 6-ohm speakers, set the unit’s speaker
impedance to “6 Ω MIN”. For details, see “Setting the speaker
impedance” in the Owner’s Manual.
Before connecting the speakers, remove the unit’s power
cable from the AC wall outlet and turn off the subwoofer.
Ensure that the core wires of the speaker cable do not touch
one another or come into contact with the unit’s metal parts.
Doing so may damage the unit or the speakers. If the speaker
cables short circuit, “Check SP Wires” will appear on the front
display when the unit is turned on.
4
Connecting external devices
5
Connecting the power cable to an
AC wall outlet
Before connecting the power cable (Taiwan and General
models only)
Set the switch position of VOLTAGE SELECTOR according to
your local voltage.
Voltages are AC 110–120/220–240 V, 50/60 Hz.
1
Аксессуары, используемые с этим
документом
1
Пульт ДУ
2
Батарейки (AAA, R03, UM-4) (2 шт.)
3
Микрофон YPAO
Следующие кабели (не входят в комплект) необходимы для
построения системы, описанной в этом документе.
Кабели для колонок (5 шт.)
Штекерный аудиокабель (1 шт.)
Кабели HDMI (3 шт.)
2
Расположение колонок
Расставьте колонки в помещении, руководствуясь
приведенной схемой.
1 Фронтальная колонка (левая)
2 Фронтальная колонка (правая)
3 Центральная колонка
4 Колонка окружающего звучания (левая)
5 Колонка окружающего звучания (правая)
9 Сабвуфер
3
Подключение колонок и сабвуфера
Только модели для США и Канады
При подключении колонок с импедансом 6 Ом установите
для импеданса колонок аппарата значение “6 Ω MIN”.
Дополнительные сведения см. в разделе “Настройка
импеданса колонок” в “Инструкции по эксплуатации”.
Перед подключением колонок извлеките из настенной
розетки переменного тока кабель питания аппарата и
выключите сабвуфер.
Убедитесь, что жилы кабеля колонки не соприкасаются
между собой и не контактируют с металлическими
деталями аппарата.
Это может привести к повреждению аппарата или
колонок. В случае короткого замыкания цепи кабеля
колонки при включении аппарата на дисплее передней
панели появится сообщение “Check SP Wires”.
4
Подключение внешних устройств
5
Подключение кабеля питания к
настенной розетке переменного тока
Перед подключением кабеля питания (только модель для
Тайваня и общая модель)
Установите переключатель VOLTAGE SELECTOR (Выбор
напряжения) в соответствии с местным стандартом
напряжения.
Доступны напряжения 110–120 В или 220–240 В переменного
тока, 50/60 Гц.
EnglishРусский
Сабвуфер
Subwoofer
9
Используйте
сабвуфер, оснащенный
встроенным
усилителем.
Use a subwoofer
equipped with built-in
amplier.
Колонка окружающего
звучания (правая)
Surround speaker (R)
5
Колонка окружающего
звучания (левая)
Surround speaker (L)
4
Центральная колонка
Center speaker
3
Фронтальная колонка (правая)
Front speaker (R)
2
Фронтальная колонка (левая)
Front speaker (L)
1
В настенную
розетку
переменного тока
To an AC wall outlet
TB
TV
Вход HDMI
HDMI input
Выход HDMI
HDMI output
Выход HDMI
HDMI output
BD/DVD-проигрыватель
BD/DVD player
Приставка для воспроизведения
спутникового/кабельного сигнала
Satellite/cable set top box
3
4
5
Штекерный аудиокабель
Audio pin cable
VOLTAGE SELECTOR
(только модель для Тайваня и
общая модель)
(Taiwan and General models only)
Аппарат
The unit
10–30°
10° to 30°
10–30°
10° to 30°
10 мм
10 mm
10 мм
10 mm

Other manuals for Yamaha RX-V477

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yamaha RX-V477 and is the answer not in the manual?

Yamaha RX-V477 Specifications

General IconGeneral
Receiver typeSurround
Audio output channels5.1 channels
Dynamic power per channel (4 Ohm)130 W
Power output per channel (1KHz@6 Ohm)115 W
Power output per channel (20-20KHz@8 Ohm)- W
HDMI in6
Audio (L/R) in4
Composite video in2
Component video (YPbPr/YCbCr) in1
Headphone connectivity6.3 mm
Component video (YPbPr/YCbCr) out0
Speakers connectivity typeBanana connector/Binding posts
Wi-FiNo
Ethernet LANYes
Supported radio bandsAM, FM
Display-
Product colorTitanium
Audio decodersDolby Digital Plus, Dolby TrueHD, DTS-HD Master Audio
Apple docking compatibilityiPhone, iPod
Power consumption (standby)0.1 W
Weight and Dimensions IconWeight and Dimensions
Depth315 mm
Width435 mm
Height161 mm
Weight8000 g

Related product manuals