Why my Yamaha Receiver fails to turn on?
If your Yamaha Receiver fails to turn on or suddenly goes into standby mode, make sure the power cord is firmly plugged in. Also, check that the IMPEDANCE SELECTOR switch on the rear panel is set to either end while the unit is in standby mode.
What to do if the sound suddenly goes off on Yamaha RX-V795?
If the sound suddenly goes off on your Yamaha Receiver, the protection circuit may have been activated due to a short circuit. Put the unit into standby mode, and then turn it back on to reset the protection circuit. Also, check if the SLEEP timer is activated and cancel it if necessary.
Why Yamaha Receiver remote controller does not function properly?
If your Yamaha Receiver remote controller isn't functioning properly, make sure you are within a 6-meter range and no more than 30 degrees off-axis from the front panel. Also, check if direct sunlight or lighting is interfering with the remote control sensor on the main unit; if so, change the position of the main unit.
Why only one speaker works on my Yamaha RX-V795 Receiver?
If only one speaker is outputting sound on your Yamaha Receiver, check the BALANCE control setting and adjust it to the appropriate position. Also, verify that the cords are connected properly; if the problem continues, the cords may be defective.
Why is there no sound from the center speaker on my Yamaha RX-V795 Receiver?
If there is no sound from the center speaker on your Yamaha Receiver, check that the function “1. CENTER SPEAKER” in the SET MENU mode is not set to “NONE”. Select the appropriate position. Also, if you are using one of the DSP programs No. 6 to No. 10 with a 2-channel stereo input signal, select another program. Finally, if the input signals encoded with Dolby Digital or DTS do not have center channel signals, refer to the instructions for the source currently played.
Why there is no sound from the effect speakers of my Yamaha RX-V795?
If there is no sound from the effect speakers on your Yamaha Receiver, first ensure that the EFFECT button is turned on. Also, if you are using a Dolby Surround (or DTS) decoding program with material not encoded with Dolby Surround (or DTS), try using a different sound field program.
What to do if my Yamaha RX-V795 Receiver has no sound or picture?
If your Yamaha Receiver isn't producing sound or picture, verify the output cord connections are correct and secure. If the issue continues, the cords may be defective. Also, ensure the appropriate input source is selected using the INPUT SELECTOR or the TAPE/MD MON/EXT. DECODER button. Check that the speaker connections are secure. Finally, confirm that the source signals are compatible with the unit, such as PCM audio or Dolby Digital/DTS encoded signals.
How to stop Yamaha RX-V795 Receiver from humming?
If your Yamaha Receiver is humming, firmly connect the audio plugs. If the problem persists, the cords may be defective. Also, ensure the turntable is properly connected to the GND terminal.
What to do if my Yamaha RX-V795 does not work normally?
If your Yamaha Receiver is not working normally, it might be due to strong external noise or a misoperation. Turn the unit into standby mode and disconnect the AC power cord from the AC outlet. After about 30 seconds, reconnect the power and operate the unit again.
How to improve bass on Yamaha Receiver?
If you're experiencing poor bass reproduction with your Yamaha Receiver, and you don't have a subwoofer, check that the function “4. LFE/BASS OUT” in the SET MENU mode is set to “MAIN”. Also, ensure that the output mode selection for each channel (MAIN, CENTER or REAR) is suitable for your speaker system.
Explains symbols used for warnings and instructions.
Explains the Digital Sound Field Processor technology.
Details Yamaha's research in recreating acoustic environments.
Explains the Dolby Pro Logic Surround system and its features.
Lists the accessories included with the unit.
Guides on how to install batteries in the remote.
Provides notes on battery replacement and operation range.
Details the functions of the front panel controls.
Explains the indicators and information shown on the unit's display.
Guides on setting up the speaker system and placement.
Details proper placement for main, center, and rear speakers.
Illustrates 5 and 4 speaker system setups.
Explains how to connect audio/video source equipment.
Describes front panel terminals for connecting camcorders.
Guides on connecting digital audio sources.
Explains connecting via RF demodulator for Dolby Digital.
Guides on connecting S-Video sources for high quality picture.
Explains connecting 6-channel audio inputs for future formats.
Explains speaker connection basics and polarity.
Guides on setting speaker impedance for proper operation.
Explains connecting AM and FM antennas.
Instructions on connecting the AC power cord and using outlets.
Explains how to display information on the monitor screen.
Selects speaker output modes for optimal system performance.
Describes how to change settings using the unit or remote.
Adjusts sound output levels for balanced speaker sound.
Step-by-step guide to select and play an audio/video source.
Adjusts audio settings like balance, bass, treble, and tone bypass.
Explains automatic and manual tuning methods for radio stations.
Guides on storing and recalling radio stations.
Guides on activating DSP programs for enhanced audio.
Sets individual speaker output levels.
Introduces 13 functions to maximize system performance.
Guides on customizing DSP program parameters.
Explains how to adjust DSP program parameters.
Details various DSP parameters and their effects.
Explains how to select components and press keys.
Lists components controllable by selector dial positions.
Details functions of remote keys based on selector dial position.
Guides on entering manufacturer codes for component control.
Resets remote control codes to factory defaults.
Lists common problems and solutions for the unit's general operation.
Troubleshoots issues with the remote controller not working.
Solves problems related to FM/AM reception and tuning.
Addresses issues with DTS playback, including noise.
Lists technical specifications for the audio components.
Lists technical specifications for the video components.
Lists technical specifications for the FM tuner.
Lists technical specifications for the AM tuner.
Provides general technical specifications like power and dimensions.
Lists manufacturer codes for TV control.
Lists manufacturer codes for cable box control.
Lists manufacturer codes for DBS tuner control.
Lists manufacturer codes for VCR control.
Lists manufacturer codes for MD recorder control.
Lists manufacturer codes for tape deck control.
Lists manufacturer codes for LD player control.
Lists manufacturer codes for CD player control.
Lists manufacturer codes for DVD player control.
General| Type | AV Receiver |
|---|---|
| Amplifier Type | Discrete |
| Channels | 5.1 |
| Frequency Response | 20 Hz - 20 kHz |
| Input Sensitivity | 200 mV |
| Signal-to-Noise Ratio | 100 dB |
| Analog Inputs | 5 |
| Surround Sound | Dolby Digital, DTS |
| Digital Inputs | 2 x Coaxial |
| Video Connections | Composite, S-Video |
| Weight | 11 kg |
To Next Page
