York D1EB036 - Typical Wiring Diagram Legend; Typical Wiring Diagram Notes

173858-YIM-A-0306
Unitary Products Group 17
FIGURE 5 - TYPICAL WIRING DIAGRAM LEGEND
FIGURE 6 - TYPICAL WIRING DIAGRAM NOTES
&%
&2035
)
)=
+3
.
.
/3
0
0
0
5&
5&
63
63
63
63
7
&,5&8,7%5($.(59$03
&2035(6625
)86(96(&21'$5<$03
)5((=(67$76:,7&+237,21$&&(6625<23(1#)
+,*+35(6685(6:,7&+237,21$/$&&(6625<23(16$736,*
5(/$<,1'225)$102725
5(/$<(/(&75,&+($7(5
/2:35(6685(6:,7&+237,21$/$&&(6625<23(1#36,*
&217$&725&2035(6625287'225)$1
&217$&725(/(&75,&+($79&2,/
&217$&725(/(&75,&+($79&2,/
287'225)$1581&$3$&,725$/7(51$7(
,1'225)$1581&$3$&,725
62&.(73/8*&211(&7,2121)$1&21752/%2$5'/2:92/7$*(
62&.(73/8*&211(&7,2121)$1&21752/%2$5'/,1(92/7$*(
62&.(73/8*&211(&7,2121,')$1027259
62&.(73/8*&211(&7,2121,')$1027259
75$16)250(599$
,'(17,),('7(50,1$/21581&$3$&,725
52207+(50267$79&211(&7,216
7%21)$1(/(&+($7&21752/%2$5'
)$&725<:,5,1*$1''(9,&(6
237,21$/:,5,1*$1''(9,&(6
),(/':,5,1*
1. ALL FIELD WIRING TO BE ACCOMPLISHED FOLLOWING CITY, LOCAL
AND/OR NATIONAL CODES IN EFFECT AT TIME OF INSTALLATION OF
THIS UNIT.
2. CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SER-
VICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DAN-
GEROUS OPERATION. IF ANY OF THE WIRE AS SUPPLIED WITH THIS
UNIT MUST BE REMOVED, IT MUST BE REPLACED WITH TYPE 105° C,
600V WIRE OR EQUIVALENT CLEARLY RENUMBERED FOR IDENTIFICA-
TION. VERIFY PROPER OPERATION AFTER SERVICING.
3. MOTORS ARE INHERENTLY PROTECTED.
4. SEE UNIT NAMEPLATE FOR MAXIMUM FUSE SIZE AND MINIMUM CIR-
CUIT AMPACITY.
5. SELECT INDOOR BLOWER SPEED TO OBTAIN APPROX 400 CFM/TON IN
COOLING.
6. IF BOTH LR AND ASCT ARE PRESENT, WIRE 801/BL AND 805/BL ARE
CONNECTED TO ASCT-3. IF ONLY LR IS PRESENT, WIRE 801/BL AND
805/BL ARE CONNECTED TO M1 COIL. IF ONLY ASCT IS PRESENT,
WIRE 202/Y IS CONNECTED TO ASCT-3. IF NEITHER LR OR ASCT IS
PRESENT, WIRE 202/Y IS CONNECTED TO M1 COIL.
7. UNIT FACTORY WIRED FOR 415 VOLT OPERATION. FOR 380 VOLT
OPERATION MOVE ‘108/PR’ WIRE FROM 415V TO 380V ON TRANS-
FORMER T1.