What to do if my Zanussi Dishwasher does not fill with water?
If your Zanussi Dishwasher isn't filling with water, check the following: * Ensure the water tap is fully open. * Contact your local water authority to verify the water supply pressure is adequate. * Make sure the water tap isn't clogged. * Inspect the filter in the inlet hose for clogs. * Confirm the inlet hose has no kinks or bends.
Why my Zanussi ZDF26011XA Dishwasher programme does not start?
If the Zanussi Dishwasher programme isn't starting, make sure the appliance door is properly closed. Also, if the delay start is set, either cancel the setting or wait for the countdown to finish. The appliance may also be recharging the resin inside the water softener, which takes approximately 5 minutes.
What to do if my Zanussi ZDF26011XA won't drain the water?
If your Zanussi Dishwasher is not draining water, check that the sink spigot isn't clogged and ensure the drain hose has no kinks or bends.
What to do if my Zanussi ZDF26011XA Dishwasher won't start?
If your Zanussi Dishwasher program won't start, ensure the appliance door is fully closed. If the delay start function is active, either cancel the setting or wait for the countdown to finish. The appliance may also be undergoing a resin recharge, which takes about 5 minutes.
What to do if my Zanussi ZDF26011XA won't turn on?
If your Zanussi Dishwasher won't activate, ensure the mains plug is correctly connected to the mains socket and check that there is no damaged fuse in the fuse box.
What to do if my Zanussi ZDF26011XA is not draining water?
If your Zanussi Dishwasher isn't draining water, check the following: 1. Make sure the sink spigot is not clogged. 2. Ensure the filter in the outlet hose isn't clogged. 3. Verify the interior filter system is clear. 4. Confirm the drain hose has no kinks or bends.
What to do if my Zanussi ZDF26011XA is not filling with water?
If your Zanussi Dishwasher isn't filling with water, make sure the water tap is fully open and that the water supply pressure isn't too low. Also, check that the water tap isn't clogged, the filter in the inlet hose isn't clogged, and the inlet hose has no kinks or bends.
How to fix anti-flood device on Zanussi ZDF26011XA Dishwasher?
If the anti-flood device is activated on your Zanussi Dishwasher, close the water tap and contact an Authorised Service Centre.
What does it mean if my Zanussi ZDF26011XA Dishwasher stops and starts frequently?
It is normal for your Zanussi Dishwasher to stop and start during operation. This provides optimal cleaning results and energy savings.
What causes a small leak from the Zanussi Dishwasher door?
A small leak from your Zanussi Dishwasher door can be caused by the appliance not being level. Adjust the adjustable feet to correct this. Also, ensure the appliance door is centered on the tub by adjusting the rear foot.
Safety instructions for children and vulnerable users.
Instructions for installing the appliance.
Instructions and warnings for electrical hookup.
Guidelines for connecting the appliance to the water supply.
How to select a wash programme on the appliance.
How to access and change user-specific settings.
Steps to clean the appliance's filters.
Causes and solutions for inadequate washing performance.
Reasons and fixes for dishes not drying properly.
General| Type | Freestanding |
|---|---|
| Appliance placement | Freestanding |
| Control type | Buttons |
| Energy Efficiency Class | A+ |
| Number of Place Settings | 13 |
| Number of washing programs | 5 |
| Drying system | Residual heat |
| Maximum delay start | 24 hours |
| Energy consumption per cycle | 1.039 kWh |
| Annual energy consumption | 295 kWh |
| Width | 600 mm |
| Height | 850 mm |
| Inlet hose length | 1.5 m |
| Outlet hose length | 1.5 m |
| Delay Start | Yes |
| Half Load Option | No |
| Drying Class | A |
| Product size | Standard |
| Wash Programs | Eco, Intensive, Quick |
| Water consumption per cycle | 11 liters |
| Annual water consumption | 3080 liters |
| Programs | Intensive, Eco, Quick, Rinse |
To Next Page