What causes electronic interference in ZOLL M Series Medical Equipment?
Electronic interference can be caused by excessive radio frequency interference. To resolve this, check for potential sources of RFI and move patient cables away from other electrical equipment. Try turning off sources of excessive RFI or moving the M Series unit away from the RFI source.
What to do if displayed heart rate is not accurate on ZOLL Medical Equipment?
To address an inaccurate displayed heart rate, first verify that the heart rate flashes with each QRS on the display. Then, try changing the lead selection, adjusting the ECG size, and repositioning the ECG electrodes.
What does V LEADS OFF message mean on ZOLL Medical Equipment?
If you are not using V leads, attach the V lead connector terminator plug to the cable’s V lead connector. If a V1 lead wire metal snap comes into contact with the patient’s skin, the system will show all V leads as OFF. Remove V1 leads and others away from the patient, then turn off the unit and wait ten seconds before turning it back on.
What to do if my ZOLL M Series Medical Equipment shows 'CHECK CO2 LINE'?
If the ZOLL Medical Equipment displays 'CHECK CO2 LINE', it means there is a sample line blockage. First, make sure the sample line is correctly plugged into the module. Then, check that the sample line and exhaust tube are not blocked, kinked, or pinched. Also, ensure the airway adapter isn't blocked. If you find any blockages, fix them, then remove and reinsert the sample cell into the receptacle. If the problem continues, replace the sample line.
Why does my ZOLL M Series say 'CHECK CO2 SENSOR'?
If your ZOLL Medical Equipment displays 'CHECK CO2 SENSOR', it indicates that the sensor cable might not be properly connected or the sensor is overheating. Make sure the sensor cable is correctly plugged in. Also, check that the sensor isn't exposed to too much heat. If the problem continues, you may need to replace the sensor.
What does 'CHECK CO2 MODULE' mean on my ZOLL Medical Equipment?
If your ZOLL Medical Equipment shows 'CHECK CO2 MODULE', it means the module isn't plugged in correctly or is overheating. Check that the module cable is properly connected. Also, make sure the module isn't exposed to excessive heat. If the problem persists, you may need to replace the module.
Why does my ZOLL Medical Equipment say 'REPLACE CO2 SENSOR'?
If your ZOLL Medical Equipment is displaying 'REPLACE CO2 SENSOR', the sensor is likely defective or incompatible. This message appears if the 'WARM UP' message stays on for more than 5 minutes. The solution is to replace the sensor.
Why does flash or arcing occur under the defibrillator pad of ZOLL Medical Equipment?
Flash or arcing under the defibrillator pad can occur due to several reasons. Avoid using alcohol and betadine around the treatment area, as these can increase conductivity. Check for gel droop and replace the electrode if the gel has leaked. Ensure pads are correctly coupled to the patient’s skin and connected to the universal cable. Also, check for dried-out gel on the defibrillator pad and replace if expired. Clip excessive hair; do not shave. Avoid chest compressions through the pads to prevent damage. Apply the back electrode first to avoid lifting the front electrode during patient maneuvering. Make sure that wet gel pads are stored flat.
What does 'CHECK CO2 ADAPTER' mean on ZOLL M Series?
If your ZOLL Medical Equipment displays 'CHECK CO2 ADAPTER', it's usually because the airway adapter was removed from the CAPNOSTAT 3 or there's a blockage on the adapter's windows. It can also happen if you didn't zero the adapter after changing its type. To fix it, clean the airway adapter and reattach it. If the problem continues or you changed the adapter type, perform a mainstream airway adapter zero.
How long should the 'WARM UP' message display on ZOLL Medical Equipment?
If your ZOLL Medical Equipment displays 'WARM UP', the mainstream sensor or LoFlo sidestream module is warming up. Wait for the sensor or module to warm up, which can take up to 5 minutes. If the message persists for more than 5 minutes, replace the sensor or module.
General| Pacer Rate | 30 - 180 ppm |
|---|---|
| Display Type | LCD |
| Defibrillator Type | Manual and AED |
| Monitor Display | High-resolution LCD |
| ECG Monitoring | 3-lead |
| Pacing | Demand |
| Battery Type | Lithium-ion |
| Display | High-resolution LCD |
| Waveform | Biphasic Truncated Exponential (BTE) |
| Monitoring Parameters | ECG, SpO2, EtCO2, NIBP, temperature |
| Connectivity | Data port for data transfer |
| Pacer Type | Transcutaneous |
| Pacer Output | 0 - 140 mA |
| Printer | Integrated thermal |
| Energy Selection | 2, 3, 5, 7, 10, 15, 20, 30, 50, 70, 100, 120, 150, 200 Joules |
To Next Page
