What to do if ZOLL Aed Plus shows '! UNIT FAILED'?
If the unit displays '! UNIT FAILED', turn it off and then press and hold the ON/OFF button for at least 5 seconds to perform a self-test. Also, verify that the electrode cable is properly plugged into the patient cable connector. If the problem persists, replace the electrodes.
How to fix 'CHANGE BATTERIES' prompt on ZOLL Aed Plus Medical Equipment?
If your ZOLL Medical Equipment prompts you to 'CHANGE BATTERIES,' replace all batteries with new batteries at the same time. Remember to press the Battery Reset Button when prompted.
How to fix the 'CHANGE BATTERIES' prompt on ZOLL Aed Plus Medical Equipment?
To resolve the 'CHANGE BATTERIES' prompt on your ZOLL Medical Equipment, replace all batteries with new batteries at the same time. Then, press the Battery Reset Button when prompted.
What to do if ZOLL Aed Plus Medical Equipment says 'ANALYSIS HALTED. KEEP VICTIM STILL'?
If the ZOLL Medical Equipment displays 'ANALYSIS HALTED. KEEP VICTIM STILL', it means excessive artifact was detected during ECG analysis. Ensure the victim is motionless during ECG analysis, and that no one touches the victim during analysis. If you're using the device in an emergency vehicle, bring the vehicle to a halt before performing ECG analysis.
Why was no shock delivered by my ZOLL Medical Equipment?
A shock might not be delivered for these reasons: 1. The Treatment button wasn't pressed within 30 seconds of being prompted. 2. An internal error occurred. If you failed to press the button in time, make sure to press it when prompted within 30 seconds. If an internal error occurred, remove the unit from service and contact Technical Service.
What does '! RELEASE SHOCK BUTTON' mean on ZOLL Aed Plus?
If you see '! RELEASE SHOCK BUTTON' (or '! RELEASE TREATMENT BUTTON'), release the Treatment button. Do not press the button until the charge-ready tone sounds and the button begins flashing.
What to do if the ZOLL Aed Plus prompts 'PLUG IN CABLE'?
If the ZOLL Medical Equipment prompts 'PLUG IN CABLE', check the cable connection between the electrodes and the unit.
What to do if ZOLL Medical Equipment prompts 'RELEASE SHOCK BUTTON'?
If the ZOLL Medical Equipment prompts 'RELEASE SHOCK BUTTON', release the Shock Button, then press and hold it again until discharge occurs.
What to do if ZOLL Aed Plus prompts to 'RELEASE SHOCK BUTTON'?
If your ZOLL Medical Equipment prompts you to 'RELEASE SHOCK BUTTON', release the Shock Button, then press and hold the Shock Button until discharge occurs. If the voice prompt continues, consider contacting ZOLL Technical Service.
What to do if ZOLL Aed Plus self test failed?
If the self-test failed on your ZOLL Medical Equipment, initiate a manual self-test by pressing and holding the ON/OFF Button for more than 5 seconds. Attempt to repair the device by replacing the batteries or electrodes. If the AED Plus fails the test again, remove the AED Plus from service.
Provides warnings about servicing the unit and potential lethal shocks.
Contact information and procedures for obtaining technical service for the AED Plus unit.
Procedure to ensure the unit shows no signs of damage or excessive wear.
Verifies the AED Plus unit is working properly and ready for use.
Initiates the unit's self-diagnostic procedure to verify key functions.
Provides common issues, solutions, and operator/technical actions for problems.
Lists critical error log messages that indicate the unit requires technical service.
Guidance on using the maintenance checklist for record-keeping.
General| Device Type | Automated External Defibrillator (AED) |
|---|---|
| Waveform | Rectilinear Biphasic |
| Electrode Shelf Life | 5 years |
| IP Rating | IP55 (protected against dust and water jets) |
| Warranty | 5 years |
| Energy | 120J, 150J, 200J |
| CPR Feedback | Real CPR Help |
| Battery Type | 10 x 123A lithium batteries |
| Battery Life | 5 years |
| Display | LCD |
| Weight | 6.7 lbs (3.1 kg) |
| Dimensions | 5.25 in (H) x 9.50 in (W) x 11.50 in (D) / 13.3 cm (H) x 24.1 cm (W) x 29.2 cm (D) |
| Energy Selection | Fixed |
| Voice Prompts | Yes |
| Data Recording | Internal memory |
| Operating Temperature | 0°C to 50°C (32°F to 122°F) |
| Storage Temperature | -4°F to 140°F (-20°C to 60°C) |
| Relative Humidity | 10% to 95% non-condensing |
| Altitude | Up to 15, 000 feet (4, 572 meters) |
To Next Page
