Why is my ZOLL Medical Equipment beeping when off?
If your ZOLL Medical Equipment is beeping when it's turned off, remove it from service and replace the batteries. Make sure to replace all batteries at the same time. Press the battery reset button after replacing them. If the beeping continues after these steps, contact ZOLL Technical Service.
Why does my ZOLL Aed Plus say 'ANALYSIS HALTED. KEEP PATIENT STILL'?
If the ZOLL Medical Equipment displays the 'ANALYSIS HALTED. KEEP PATIENT STILL' prompt, it means excessive artifact was detected during ECG analysis. To resolve this, ensure the patient remains motionless during ECG analysis, and avoid touching the patient. If you're using the device in an emergency vehicle, stop the vehicle before performing ECG analyses.
What to do if ZOLL Medical Equipment prompts 'RELEASE SHOCK BUTTON'?
If the ZOLL Medical Equipment prompts 'RELEASE SHOCK BUTTON', release the Shock Button, then press and hold it again until discharge occurs.
What to do if the ZOLL Aed Plus prompts 'PLUG IN CABLE'?
If the ZOLL Medical Equipment prompts 'PLUG IN CABLE', check the cable connection between the electrodes and the unit.
What to do if my ZOLL Aed Plus Medical Equipment is beeping when off?
If your ZOLL Medical Equipment is beeping when turned off, remove the unit from service and replace the batteries. Ensure you replace all batteries at the same time with new ones and press the Battery Reset Button when prompted. If the beeping continues, further assistance is needed.
How to change batteries in ZOLL Aed Plus?
If your ZOLL Medical Equipment prompts 'CHANGE BATTERIES', replace all batteries with new ones at the same time. Remember to press the Battery Reset Button when prompted after the replacement.
What to do if the ZOLL Aed Plus Medical Equipment displays 'ANALYSIS HALTED. KEEP PATIENT STILL'?
If the ZOLL Medical Equipment displays 'ANALYSIS HALTED. KEEP PATIENT STILL', it means excessive artifact was detected during ECG analysis. Ensure the patient is motionless during ECG analysis and that no one touches the patient during analysis. If you're using the device in an emergency vehicle, stop the vehicle before performing ECG analysis. Keep the patient still.
What to do if ZOLL Aed Plus shows a red 'X' or beeps when off?
If your ZOLL Medical Equipment is showing a red “X” in the status indicator window or making a beeping noise when the unit is off, you should: 1. Perform a manual test. 2. Check that the cable is properly attached to the unit. 3. Replace the batteries. If the unit still does not operate correctly after these steps, remove it from service.
What to do if ZOLL Medical Equipment shows a red 'X' in the status indicator window when on?
If the ZOLL Medical Equipment shows a red “X” in the status indicator window when the unit is on, power cycle the unit. If the red “X” is still present, remove the unit from service.
What to do if ZOLL Aed Plus prompts to 'RELEASE SHOCK BUTTON'?
If your ZOLL Medical Equipment prompts you to 'RELEASE SHOCK BUTTON', release the Shock Button, then press and hold the Shock Button until discharge occurs. If the voice prompt continues, consider contacting ZOLL Technical Service.
Provides warnings about servicing the unit and potential lethal shocks.
Contact information and procedures for obtaining technical service for the AED Plus unit.
Procedure to ensure the unit shows no signs of damage or excessive wear.
Verifies the AED Plus unit is working properly and ready for use.
Initiates the unit's self-diagnostic procedure to verify key functions.
Provides common issues, solutions, and operator/technical actions for problems.
Lists critical error log messages that indicate the unit requires technical service.
Guidance on using the maintenance checklist for record-keeping.
General| Device Type | Automated External Defibrillator (AED) |
|---|---|
| Waveform | Rectilinear Biphasic |
| Electrode Shelf Life | 5 years |
| IP Rating | IP55 (protected against dust and water jets) |
| Warranty | 5 years |
| Energy | 120J, 150J, 200J |
| CPR Feedback | Real CPR Help |
| Battery Type | 10 x 123A lithium batteries |
| Battery Life | 5 years |
| Display | LCD |
| Weight | 6.7 lbs (3.1 kg) |
| Dimensions | 5.25 in (H) x 9.50 in (W) x 11.50 in (D) / 13.3 cm (H) x 24.1 cm (W) x 29.2 cm (D) |
| Energy Selection | Fixed |
| Voice Prompts | Yes |
| Data Recording | Internal memory |
| Operating Temperature | 0°C to 50°C (32°F to 122°F) |
| Storage Temperature | -4°F to 140°F (-20°C to 60°C) |
| Relative Humidity | 10% to 95% non-condensing |
| Altitude | Up to 15, 000 feet (4, 572 meters) |
To Next Page
