How to resolve 'PLUG IN CABLE' prompt on ZOLL Medical Equipment?
If your ZOLL Medical Equipment displays a 'PLUG IN CABLE' prompt, check the cable connection between the electrodes and the AED Plus.
What to do if ZOLL Aed Plus self test failed?
If the self-test failed on your ZOLL Medical Equipment, initiate a manual self-test by pressing and holding the ON/OFF Button for more than 5 seconds. Attempt to repair the device by replacing the batteries or electrodes. If the AED Plus fails the test again, remove the AED Plus from service.
What to do if there is a red “X” in the status indicator window on ZOLL Aed Plus Medical Equipment?
If you see a red “X” in the status indicator window of your ZOLL Medical Equipment, initiate a manual self-test by pressing and holding the ON/OFF Button for more than 5 seconds. Check if the cable is properly attached to the AED Plus, or replace the electrodes. Cycle the power on the AED Plus by turning the unit off and then on again. Replace all batteries at the same time with new batteries that are less than 1 year old and press the Battery Reset Button when prompted. If the AED Plus still does not operate correctly, remove the unit from service.
Why does my ZOLL Aed Plus say 'ANALYSIS HALTED. KEEP VICTIM STILL'?
The 'ANALYSIS HALTED. KEEP VICTIM STILL' prompt on your ZOLL Medical Equipment indicates that excessive artifact was detected during ECG analysis. Ensure the victim is motionless during ECG analysis and that no one is touching the victim. If using the AED Plus in an emergency vehicle, bring the vehicle to a halt before performing ECG analysis. The victim must be still.
How to fix a failed self test on ZOLL Aed Plus?
If the self-test fails on your ZOLL Medical Equipment, initiate a manual self-test by pressing and holding the ON/OFF Button for more than 5 seconds. Then attempt to repair the device by replacing the batteries or electrodes. If the device fails the test again, remove it from service and contact ZOLL Technical Service.
What to do if ZOLL Aed Plus Medical Equipment says 'PLUG IN CABLE'?
If your ZOLL Medical Equipment prompts 'PLUG IN CABLE', check the cable connection between the electrodes and the device.
What to do if ZOLL Aed Plus Medical Equipment has a red 'X'?
If your ZOLL Medical Equipment displays a 'Red “X”' in the status indicator window, initiate a manual self-test by pressing and holding the ON/OFF Button for more than 5 seconds. Also, check if the cable is properly attached or replace the electrodes. You can also try cycling the power by turning the unit off and then on again. Replace all batteries with new ones that are less than 1 year old and press the Battery Reset Button when prompted. If the issue persists, remove the unit from service and contact ZOLL Technical Service.
What to do if ZOLL Aed Plus Medical Equipment says 'ANALYSIS HALTED. KEEP VICTIM STILL'?
If the ZOLL Medical Equipment displays 'ANALYSIS HALTED. KEEP VICTIM STILL', it means excessive artifact was detected during ECG analysis. Ensure the victim is motionless during ECG analysis, and that no one touches the victim during analysis. If you're using the device in an emergency vehicle, bring the vehicle to a halt before performing ECG analysis.
How to fix the 'CHANGE BATTERIES' prompt on ZOLL Aed Plus Medical Equipment?
To resolve the 'CHANGE BATTERIES' prompt on your ZOLL Medical Equipment, replace all batteries with new batteries at the same time. Then, press the Battery Reset Button when prompted.
How to fix 'CHANGE BATTERIES' prompt on ZOLL Aed Plus Medical Equipment?
If your ZOLL Medical Equipment prompts you to 'CHANGE BATTERIES,' replace all batteries with new batteries at the same time. Remember to press the Battery Reset Button when prompted.
Provides warnings about servicing the unit and potential lethal shocks.
Contact information and procedures for obtaining technical service for the AED Plus unit.
Procedure to ensure the unit shows no signs of damage or excessive wear.
Verifies the AED Plus unit is working properly and ready for use.
Initiates the unit's self-diagnostic procedure to verify key functions.
Provides common issues, solutions, and operator/technical actions for problems.
Lists critical error log messages that indicate the unit requires technical service.
Guidance on using the maintenance checklist for record-keeping.
General| Device Type | Automated External Defibrillator (AED) |
|---|---|
| Waveform | Rectilinear Biphasic |
| Electrode Shelf Life | 5 years |
| IP Rating | IP55 (protected against dust and water jets) |
| Warranty | 5 years |
| Energy | 120J, 150J, 200J |
| CPR Feedback | Real CPR Help |
| Battery Type | 10 x 123A lithium batteries |
| Battery Life | 5 years |
| Display | LCD |
| Weight | 6.7 lbs (3.1 kg) |
| Dimensions | 5.25 in (H) x 9.50 in (W) x 11.50 in (D) / 13.3 cm (H) x 24.1 cm (W) x 29.2 cm (D) |
| Energy Selection | Fixed |
| Voice Prompts | Yes |
| Data Recording | Internal memory |
| Operating Temperature | 0°C to 50°C (32°F to 122°F) |
| Storage Temperature | -4°F to 140°F (-20°C to 60°C) |
| Relative Humidity | 10% to 95% non-condensing |
| Altitude | Up to 15, 000 feet (4, 572 meters) |
To Next Page
