Need help?Do you have a question about the Zte IDU and is the answer not in the manual?
General| Category | Wireless Router |
|---|---|
| Wireless Standards | IEEE 802.11b/g/n |
| Frequency Band | 2.4 GHz |
| Ethernet Ports | 4 x 10/100 Mbps |
| Security Features | WEP, WPA, WPA2, WPS |
| Model | Zte IDU |
| Antenna | 2 x External Antennas |
Ensure you have a set of installed ODU.
A network cable is required for setup.
View the device label for default information.
Connect to the Wi-Fi network using the default SSID and password found on the device label.
Connect via LAN port using a network cable (RJ45) to access the Internet.
Steps to make a call: pick up handset, dial number, and wait for connection.
Press WPS button on device, enable WPS on client, and follow prompts to establish connection.
Indicates power status: On for normal, Off for abnormal.
Indicates Wi-Fi status: On for normal, Blinking for WPS, Off for disabled.
Signal level panel showing ODU signal strength from weak to strong.
Button to activate the WPS function.
Restore factory default configurations by pressing and holding.
Port to connect the power adapter.
Port to connect a telephone.
Ports for network devices; WAN port connects to POE.
Check wait time, signal strength, or potential device/cable fault.
Remove nearby electrical appliances or check cable/phone set for faults.
Ensure phone is on hook and try again, or contact service provider.
Press '#' key or wait 4-8 seconds after dialing to connect call.
Check configuration, initialization time, and network indicators.
Speed depends on signal strength and network type.
Enter correct IP, use one network adapter, and avoid proxy servers.
Ensure Wi-Fi is active, refresh list, select correct SSID, and enter correct key.
Check device label for Wi-Fi/web page password; reset device if forgotten.
Get help via email to mobile@zte.com.cn or by visiting www.ztedevices.com.
Copyright © 2021 ZTE CORPORATION. All rights reserved.
ZTE reserves the right to modify specifications without prior notice.
Images and content may differ from actual product or software.
ZTE logos are trademarks of ZTE Corporation.
Locate device away from other electronics to avoid interference.
Consult physician if device interferes with medical devices like hearing aids.
Keep at least 20 centimeters away from your device.
Do not use in environments with explosive gases or products.
Use original or authorized accessories to avoid performance issues or damage.
Do not attempt to dismantle the device; no user-serviceable parts.
Avoid contact with liquid or moisture; do not immerse in liquid.
Do not place objects on the device to prevent overheating.
Place the device in a well-ventilated environment for use.
Do not expose to direct sunlight or hot areas to maintain device life.
Do not allow children to play with the device or power adapter.
The device is for indoor use only.
Ensure socket-outlet for pluggable equipment is easily accessible.
Use an antistatic cloth; avoid chemical/abrasive cleansers. Turn off device before cleaning.
Warranty excludes defects from abrasion, misuse, unauthorized modifications, or external events.
End users cannot reject, return, or get a refund for products under excluded situations.
Warranty is the sole remedy; liability is limited as stated.
ZTE not liable for indirect, special, or consequential damages, including lost profits.
Device designed not to exceed FCC RF energy limits; operates at multiple power levels.
FCC SAR limit is 1.6 W/kg; tests conducted at highest power levels.
Highest reported SAR value for near body is 0.51 W/kg.
Maintain 10 mm separation for body operation compliance; use belt clips or holsters.
Complies with FCC Part 15; subject to conditions of no harmful interference.
Unauthorized modifications may void user's authority to operate equipment.
Steps to correct harmful interference: reorient antenna, increase separation, use different circuit.
Complies with Industry Canada license-exempt RSS standard(s).
Class B digital apparatus complies with Canadian ICES-003.
EUT compliance with SAR limits; maintain minimum 1.5 cm separation from body.
To Next Page
