100 ppm 40 mins
500 ppm 20 mins
1000 ppm 60 mins
5000 ppm 20 mins
Group
Group 1 Group 2 Group 3 Group 4
Max Concentration (ppm) Max Usage Time (mins)
Acetaldehyde
Bromomethane
Acetone
Bromomethane
Butane
Chloroethane
Cyclopentadiene
DibromodiÀuoromethane
Diethyl ether
Dimethyloxymethane
Ethylformate
Methyl acetate
Methyl propane
1,3-butadiene
2-Propenal (acrolein)
1,1-Dichloroethene Ethylene Oxide
Propanal
Vinyl Chloride
Propyleneimine
Methyl Alcohol
Iodomethane
Ethanethiol
1,1-Dimethylethylamine
Dimethyl ether
Diethyl amine
3-Chloro-1-propene (Check
local regulations)
n-Pentane
Carbon disulphide
Carbonyl Àuoride
1,2-Dichloro-1,1,2,2-tetraÀuoroethane
Diazomethane
1,1-Dimethylhydrazine
BromotriÀuoromethane
ChlorodiÀuoromethane
Chloromethane
DichlorodiÀuoromethane
DichloroÀuoromethane
1,1-DiÀuoroethane
Ketene
Methyl acetylene
Propane
TrichloroÀuoromethane
1,1,2,Trichloro -1,2,2 triÀuoroethane
Dimethylamine
Ethylamine
Formaldehyde
Methanethiol
2-Propanethiol
Trichlorosilane
Trimethyl amine
Group 1 Low boiling point organic vapours with a WEL (Workplace Exposure Limit) of less than or equal to 10 ppm or which have a short
service life. Check local regulations for WEL in your country
Low boiling point organic vapours where protection is provided by ¿lters other than AX (e.g. B, E or K).
Low boiling point organic vapours with an WEL greater than 10 ppm.
Low boiling point organic vapours where no or insuf¿cient protection is provided by gas ¿lters
Group 2
Group 3
Group 4
Group 2
Group 1
Group 3
Group 4
3M™ 6098 AXP3 NR Filter only
Limitations on the use of these ¿lters may differ from one country to another but in the absence of any limitations in
your country the following should be applied.
a) Low boiling point organic compounds will be divided into four groups.
APPROVALS
These products are type approved and audited annually by BSI, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes MK5 8PP, UK, Noti¿ed Body No.
0086. They meet standard EN 14387:2004 + A1:2008, Respiratory protective devices – gas ¿lter(s) and combined Filter(s).
b) Against compounds of groups 1 and 2, AX ¿lters complying with EN14387 can be used up to the maximum concentrations shown in the table below or 20
x WEL, whichever is lower.
c) Only new, unused ¿lters from their original packaging should be ¿tted to your facepiece. During one 8 hour shift, repeated use of an AX ¿lter is permitted,
provided the maximum usage time shown in the table above is not exceeded.
d) Use of AX ¿lters against mixtures of low boiling point organic compounds or mixtures of low boiling point organic compounds and other compounds is not
permitted as one or more of these compounds may be desorbed.
e) AX ¿lters may be used as A2 ¿lters ONLY if no other low boiling point organic compound is present. A1 or A2 ¿lters are not to be used against low boiling
point organic compounds.
FzB
Veuillez lire parallèlement à cette notice, la notice d’Instructions de la pièce faciale 3M™ où vous trouverez de plus amples renseignements sur
• Les combinaisons appropriées de masques 3M™ et de ¿ltres 3M™
• Les accessoires
• Les pièces détachées
Pour obtenir les combinaisons de ¿ltre/masques autorisées, reportez-vous à la Fig.1.
DESCRIPTION DU SYSTEME
Cette combinaison de masque/¿ltre est destinée à protéger l’utilisateur des gaz, vapeurs et/ou particules potentiellement nocives de l'atmosphère
environnant. La capacité de ¿ltration des ¿ltres est détaillée dans les Fiches Techniques.
^
Une attention particulière doit être portée aux limites d'utilisations indiquées.
5
To Next Page
Loading...
Need help?
General
