ABB HT597151 - Page 142

Operation Manual / 4 Product description / A100-M axial
Tables
© Copyright 2020 ABB. All rights reserved. HZTL4033_EN Revision E May 2020
Tables
Table1: Related documents .......................................... 3
Table2: Weight of complete turbocharger unit....... 8
Table3: Foot screws, dimension and strength class..
14
Table4: Foot screws, dimension CE.......................... 14
Table5: Foot screws, dimension TE.......................... 14
Table6: Foot screws, number of cup springs ......... 14
Table7: Torque-controlled tightening of the pres-
sure screws .................................................................... 17
Table8: Oil pressure range.......................................... 21
Table9: Oil temperature at the inlet ......................... 22
Table10: Oil temperature at the outlet .................... 22
Table11: Expected replacement intervals ................ 32
Table12: Recommended replacement intervals ..... 32
Table13: Tightening torque (81272) ......................... 36
Table14: Tightening torque (81273)......................... 36
Table15: Compressor cleaning parameters ........... 40
Table16: Compressor cleaning parameters ........... 43
Table17: Cleaning parameters Wet cleaning of tur-
bine and nozzle ring..................................................... 49
Table18: Malfunctions when starting – Delayed
start-up .......................................................................... 50
Table19: Malfunctions when starting – Vibrations 50
Table20: Malfunctions when starting – Rubbing of
rotating parts................................................................ 50
Table21: Malfunctions during operation – Lubricat-
ing oil pressure too low................................................ 51
Table22: Malfunctions during operation – Drop in
speed ............................................................................... 51
Table23: Malfunctions during operation – Speed in-
creases ............................................................................ 51
Table24: Malfunctions during operation – Exhaust
gas temperature too high .......................................... 52
Table25: Malfunctions during operation – Charge air
pressure too low........................................................... 52
Table26: Malfunctions during operation – Charge air
pressure too high ......................................................... 53
Table27: Surging of the turbocharger..................... 53
Table28: Malfunctions when stopping – Runout
noises............................................................................... 54
Table29: Malfunctions when stopping – Shortened
runout time ..................................................................... 54
Table30: Malfunction, No speed measurement sig-
nal or poor signal amplitude ....................................... 55
Table31: Malfunction, Measured speed too high ... 55
Table32: Malfunction, Measured speed too low..... 55
Table33: Assembly weights ........................................ 58
Table34: Axial clearance A........................................... 61
Table35: Tightening torque (56014) ......................... 73
Table36: Tightening torque (57005)......................... 74
Table37: Tightening torque (61069) ......................... 76
Table38: Tightening torque (61059 / 42128)........... 78
Table39: Tightening torque(86505)......................... 79
Table40: Inner thread size (25008) ........................... 80
Table41: Tightening torque (25013).......................... 81
Table42: Tightening torque (61037).......................... 82
Table43: Tightening torque, nuts that are difficult
to access (61037) ........................................................... 82
Table44: Tightening torque (61090)......................... 82
Table45: Tightening torque (77015).......................... 83
Table46: Tightening torque (72011).......................... 85
Table47: Axial clearance A ........................................... 86
Table48: Tightening torque(72027) ......................... 87
Table49: Tightening torque(72027) ......................... 88
Table50: Tightening torque (56014)......................... 92
Table51: Tightening torque (61009) ......................... 92
Table52: Tightening torques ...................................... 94
Table53: Tightening torques 61009.......................... 95
Table54: Locking device tightening torque ............ 98
Table55: Cover plate dimensions 1 ......................... 100
Table56: Cover plate dimensions 2 ......................... 100
Table57: Cover plate dimensions 3 ......................... 100
Table58: Customer spare part set (97070)............ 107
Page 112 / 113Page 112 / 113