Abloy EL420 - Emergency Exit Devices Installation (EN 179); Functional Check for Emergency Exits; Panic Exit Devices Installation (EN 1125); Functional Check for Panic Exits

R
EMERGENCY EXIT DEVICES INSTALLATION ACCORDING TO EN 179
The following locks and handles are approved to be installed together in an emergency exit
door. Strike plate EA321, EA322, EA323, EA324, EA325, EA326, EA327, EA328, EA329,
EA330, EA331, EA332 must be used in the installation.
Profile door locks
ABLOY®
DO 20.33.01
DO 20.33.02
IKON
DO 20.15.02
FSB
DO 20.03.01,
DO 20.03.02
HEWI
DO 20.13.01,
DO 20.13.02
SAPEX
DO 20.32.01
DO 20.32.02
EL420
EL422
e.g. ABLOY® INOXI
3-19/013/120 PZ+BL
e.g. S6B8
1016, 1023, 1056, 1070, 1080,
1088, 1090, 1117, 1118, 1119,
1137, 1146, 1155, 1160, 1161,
1162, 1177, 1178, 1191, 0612,
0616, 0617, 0619, 0625, 0627,
0628, 0646, 0662, 0665, 0680,
0681, 0682, 0688
111, 111.23,
114.23GK,
131, 132, 111X,
113X, 114X, 161X,
163X, 171X, 112X,
165X, 166X
e.g. 60-0719
Wooden and metal
door locks
ABLOY®
DO 20.33.01
DO 20.33.02
IKON
DO 20.15.02
SAPEX
DO 20.32.01
DO 20.32.02
EL520
EL522
e.g. ABLOY® INOXI
3-19/012/120 PZ+BL
e.g. S4K6 e.g. 60-0119
Functional check after installation:
Emergency exit (active) side and functional sensitivity tests:
- Use the handle of exit side.
- In the profile door locks the force of handle is about 15 N (approximately 1.5 kg weight at a
100 mm distance from the pivot of the handle opens the lock).
- In the wooden door locks the force of handle is about 15 N (approximately 1.5 kg weight
at a 100 mm distance from the pivot of the handle opens the lock). According to EN 179 the
force of handle must be less than 70 N.
- Close the door slowly and check that the lock deadlocks.
- Check that the bolts slide freely into the strike plate.
The safety features of this product are essential to its compliance with EN 179. No modifica-
tion of any kind, other than those described in these instrictions, are permitted.
PANIC EXIT DEVICES INSTALLATION ACCORDING TO EN 1125
The following locks and push bars are approved to be installed together on the panic exit door.
Strike plate EA321, EA322, EA323, EA324, EA325, EA326, EA327, EA328, EA329, EA330,
EA331, EA332 must be used in the installation.
Profile door locks
effeff
DO 30.04
JPM
DO 30.05
TESA
DO 30.06
EL420 8000-00-1100 (-), 8000-10-1100 (PZ)
NORMA
990000-XX-0A, 990100-XX-0A,
990001-XX-0A, 990101-XX-0A,
991000-XX-0A, 991100-XX-0A,
991001-XX-0A, 991101-XX-0A
UNIVERSAL
SERIE
19709G9xx
EL422 8000-00-1100 (-), 8000-11-1100 (RZ)
Wooden and
metal door locks
effeff
DO 30.04
EL520 8000-00-1100 (-), 8000-20-1100 (PZ)
EL522 8000-00-1100 (-), 8000-21-1100 (RZ)
Functional check after installation:
Panic exit (active) side and functional sensitivity tests:
- Push the push bar towards the door on the exit side.
- Force to open the lock by pushing the bar is about 60 N (approximately 6kg). According
to EN 1125 it must be less than 80 N.
- Close the door slowly and check that the lock deadlocks.
- Check that the bolts slide freely into the strike plate.
Note! The length ot the push bar must be at least 60 % of the width of the door.
The safety features of this product are essential to its compliance with EN 1125. No modifi-
cation of any kind, other than those described in these instrictions, are permitted.
Recommended distance from a floor to a handle or to a push bar is between
900mm - 1100mm.
Lubricate the bolts of the lock case at least once a year. Use vaseline type lubrication.
Note! Abloy Oy will not be liable for products in case these instructions are not followed.
6
!
!