Abode PROBOIL.2X - User Manual

Questions and Answers

S
Sean OwenSep 12, 2025
How to fix splashing or fast water flow from my Abode PROBOIL.2X Boiler (high pressure)?
- R
  robertwilliamsSep 12, 2025
  If the water flow rate from your Abode Boiler is faster than expected or is splashing, your incoming cold water pressure could be too high. Test your incoming cold water pressure and compare it to the recommended and maximum required pressures. Install a pressure reducing valve to your cold water mains supply if needed. Turn on the 98°C water handle only partly during use.
A
Alyssa BellSep 12, 2025
How to fix a slow 98°C water flow rate on my Abode PROBOIL.2X Boiler (blocked aerator)?
- A
  Andrea KingSep 12, 2025
  If the water flow rate from your Abode Boiler is slower than expected, the aerator on the tap end could be partly blocked with debris or calcified. Follow the aerator descale procedure in this manual.
T
Travis SullivanSep 9, 2025
How to fix a slow 98°C water flow rate on my Abode PROBOIL.2X (blocked inlet)?
- B
  Brianna OliverSep 10, 2025
  If the water flow rate from your Abode Boiler is slower than expected, your boiler inlet could be partly blocked with debris. With the water isolated, remove the blue inlet wingnut (G) and inspect the meshed inlet seal (H) underneath; clean if required.
A
Annette DelacruzSep 8, 2025
How to fix a slow 98°C water flow rate on my Abode PROBOIL.2X Boiler (blocked filter)?
- H
  Heidi VanceSep 8, 2025
  If the water flow rate from your Abode Boiler is slower than expected, your filter cartridge could be partly blocked with debris. Connect the blue flexible pipe from the filter inlet directly to the boiler (bypass the filter) to confirm; if needed, replace the filter.
L
Lauren DavisSep 7, 2025
How to fix a slow 98°C water flow rate on my Abode PROBOIL.2X (low pressure)?
- C
  Charles VillanuevaSep 7, 2025
  If the water flow rate from your Abode Boiler is slower than expected, your incoming cold water pressure could be too low. Test your incoming cold water pressure and compare it to the minimum required pressure.
T
Timothy WilliamsonAug 23, 2025
Why does 98°C water from my Abode Boiler keep flowing after turning the handle off?
- R
  Ronald RodriguezAug 23, 2025
  If the 98°C water from your Abode Boiler does not stop immediately after you turn the handle off, it's normal. There is a short delay for the pressure to equalize in the filter and boiler tank.
J
Jason HollowaySep 5, 2025
How to adjust the water temperature on my Abode Boiler?
- C
  Cheryl CrawfordSep 5, 2025
  If the water temperature from your Abode Boiler is lower or higher than expected, press the “+” & “-“ keys and check the target temperature is as expected.
P
Patricia BurtonSep 4, 2025
How to fix splashing or fast water flow from my Abode PROBOIL.2X Boiler?
- C
  Christopher CookSep 4, 2025
  If the water flow rate from your Abode Boiler is faster than expected or is splashing, the aerator on the tap could be partly blocked. Follow the aerator descale procedure in this manual.
M
monica17Sep 3, 2025
How to fix a slow 98°C water flow rate on my Abode Boiler (calcification)?
- W
  wilsonmarissaSep 3, 2025
  If the water flow rate from your Abode Boiler is slower than expected, the boiler could be calcified. Follow the boiler descale procedure in this manual.
C
cynthia41Sep 2, 2025
Why is the water temperature lower than expected on my Abode PROBOIL.2X? (spout tube issue)
- S
  Stephanie PhillipsSep 2, 2025
  If the water temperature from your Abode Boiler is lower than expected, the center spout tube in the tap may be disconnected from the aerator. See the “descaling-aerator” section for more detail.