Accutrol ACCUVALVE AVC6000 User Manual

Installation & Operation Manual - Model AVC6000
Contents of this Manual are Subject to Change Without Notification Page 6
SECTION 2 – SPECIFICATIONS
PERFORMANCE
Accuracy
+/- 5% of reading or 5 CFM, whichever is greater
Speed of Response
< 1 second control signal response (full stroke cycle time based on actuator type)
Shut-off Leakage Rate
Standard: < 1.5% FS at max operating pressure
"S" Option: < 0.5% FS round valves, < 1% FS rectangular valves @ max operating pressure
Max Operating Pressure
3”wc Differential Pressure Across Valve
Min Operating Pressure
Reference Section 2.1
Airflow Range
Reference Section 2.1
Failure Mode
Open, Closed or Last Position (based on actuator type selection)
ENVIRONMENTAL
Temperature
Airstream: -20 to 165 deg. F for all Standard Valve Models
-20 to 375 deg. F for the High Temp SS Valve Models
Ambient: -20 to 125 deg. F Storage: -40 to 165 deg. F
Humidity
0 to 90% non-condensing
ELECTRICAL
Input Power
24VAC +/- 20% 50-60Hz or 24 VDC +/- 10%
Max Power for Valve Size 06-24: 28VA or 16W for units with actuator type 3 & 5
11VA or 7W for units with actuator type 7
Max Power for Valve Size 36, 48: 51VA or 29W for units with actuator type 3 & 5
17VA or 11W for units with actuator type 7
If monitor FHM1 is connected to AVC, increase above values by 3VA or 1W
If monitor FHM3 is connected to AVC, increase above values by 6VA or 3W
Analog Inputs
AI-1; Software Configurable for Voltage or Current, 12-bit resolution
Voltage: 0-10Vdc Range, 1M ohm Impedance
Current: 0-20mA Range, 500 ohm Impedance
AI-2, AI-3; Software Configurable for Resistance range of 20K ohm or 100K ohm
500uA Current Source for 20K ohm Range, 100uA Current Source for 100K ohm Range
Digital Inputs
DI-1 and DI-2; Dry-contact inputs
Analog Outputs
AO-1 and AO-2; Software Configurable; 0-20mA, 4-20mA, 0-10v, 2-10v, 0-5v or 1-5v
12-bit Resolution, capable of driving 1K ohm load
Alarm Relay Output
SPST, NC/NO contacts, rated load 1A @ 30 vDC or 0.3A @ 125vac
Max operating voltage = 125VAC or 60 vDC
Max carry current = 1A, Max switching capacity = 37 VA, 30W
Network Com Port
EIA 485 2-wire BACnet MS/TP
Full Master Node State Machine
Data Rates 9600, 19200, 38400, 76800 and 115200
Mac address is software configurable
¼ Unit Load Receiver Input Impedance, bias & EOL termination not provided within the AVC
Configuration Port
USB 2.0, Isolated, Type C Connector, Optional Bluetooth (Ver 4.2 or later)
Status Indicators
LED Indicators for Power, Alarm, AO, BACnet, USB, AVC Status, Bluetooth & AccuNet
I/O Terminal Blocks
2 and 3 position vertical pluggable screw terminal blocks
Electromagnetic
EMC Directive 2004/108/EC
Compatibility
Low Voltage Directive 2004/108/EEC
EN61326-1:2013

Accutrol ACCUVALVE AVC6000 Specifications

General

Brand	Accutrol
Model	ACCUVALVE AVC6000
Category	Control Unit
Language	English