What causes 'CMOS Memory Size Wrong' error on Acer Aspire XC600 Desktop?
The base memory size (memory below 1MB) reported in the CMOS mismatches the actual size detected in your Acer Desktop. This can happen when the hole is set at 512K base memory or when the CMOS is corrupted.
What to do if my Acer Aspire XC600 says 'Insert BOOT diskette in A:'?
The BIOS on your Acer Desktop tried to boot from the A: drive but couldn't find a proper boot diskette. Reboot and select the correct boot device, or insert boot media into the selected boot device.
What does 'Primary Master Hard Disk Error' mean on Acer Desktop?
The IDE/ATAPI device configured as Primary Master could not be properly initialized by the BIOS in your Acer Desktop. This message typically appears when the BIOS is trying to detect and configure IDE/ATAPI devices during POST.
What does 'Primary Slave Hard Disk Error' mean on Acer Aspire XC600?
The IDE/ATAPI device configured as Primary Slave could not be properly initialized by the BIOS on your Acer Desktop. This message typically appears when the BIOS is trying to detect and configure IDE/ATAPI devices during POST.
What does 'Secondary Master Hard Disk Error' mean on Acer Desktop?
The IDE/ATAPI device configured as Secondary Master could not be properly initialized by the BIOS in your Acer Desktop. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST.
What does 'Secondary Slave Hard Disk Error' mean on Acer Desktop?
The IDE/ATAPI device configured as Secondary Slave could not be properly initialized by the BIOS in your Acer Desktop. This message typically appears when the BIOS is trying to detect and configure IDE/ATAPI devices in POST.
What to do if Acer Aspire XC600 displays 'System Halted'?
The system has been halted on your Acer Desktop. A reset or power cycle is required to reboot the machine.
What does 'Gate20 Error' mean on Acer Aspire XC600?
The BIOS is unable to properly control the mainboard’s Gate A20 function on your Acer Desktop, which controls access of memory over 1 MB. This may indicate a problem with the mainboard.
What does 'Boot Failure...' mean on Acer Aspire XC600 Desktop?
This generic message on your Acer Desktop indicates that the BIOS couldn't boot from a particular device. This message is usually followed by other information concerning the device.
What causes 'Multi-Bit ECC Error' on Acer Aspire XC600 Desktop?
A multiple bit corruption of memory has occurred in your Acer Desktop, and the ECC memory algorithm can't correct it. This might mean you have a defective memory module. Note that this message will only occur on systems using ECC enabled memory modules.
General| Product type | PC |
|---|
Records changes and updates made to the service guide with dates and versions.
Details the copyright notice and usage restrictions for the publication.
Outlines the information disclaimer and lists registered trademarks.
Explains the symbols and formatting conventions used throughout the manual.
Clarifies that the guide covers basic configurations, not localized features.
Provides guidance on ordering FRU parts and checking for updates.
Lists the supported operating systems, processors, memory, and connectivity options.
Details chassis dimensions, weight, and operating environment requirements.
Illustrates the computer's front and rear panels and identifies ports.
Explains how to access and navigate the CMOS Setup Utility for system configuration.
Details settings across Main, Advanced, Power, Security, Boot Options, and Exit menus.
Lists tools needed and pre-disassembly steps for safe component removal.
Step-by-step instructions for removing major computer components like panels, drives, and boards.
Step-by-step instructions for putting back disassembled computer parts correctly.
Covers hardware diagnostics, system checks, and external/internal inspections for problem isolation.
Explains POST checkpoints, beep codes, and common error messages for diagnostics.
Lists common error messages related to memory, boot, storage, and system configuration.
Maps symptoms to specific Field Replaceable Units (FRUs) for troubleshooting.
Details ME firmware configuration and CMOS data clearing procedures.
Covers BIOS recovery methods and procedures for updating the BIOS.
Visual representation of system components and the mainboard layout.
Explains how to set jumpers for CMOS and ME firmware.
Shows an exploded view and lists FRUs with part numbers for service.
Details processor types, speeds, cache, and major system board chips.
Specifies system memory, PCI, VGA, network, SATA, audio, and drives.
Lists specifications for BD Combo, Super Multi, and DVD-ROM drives.
To Next Page