Notice: Be sure to follow gures two and three when making your own cables.
Do not use the ground lug on the XLR connector. Do not connect the cable’s
shield conductor to the ground lug or allow the shield conductor to come in
contact with the XLR’s outer casing. Grounding the shield could cause a short
circuit and erratic behavior.
Special Note: Line Termination. When longer runs of cable are used, you
may need to use a terminator on the last unit to avoid erratic behavior. A ter-
minator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2
and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in
the female XLR connector of the last unit in your daisy chain to terminate the
line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the
possibilities of erratic behavior.
CH6 CH1 CH2 CH3 CH4 CH5 CH6
MODE R G B Macro
Mode
Speed /
Strobe
Mode Function
1 (0-31)
set color
0 0 0
0(off)
0-15 static
16-255 stro-
be speed
(0-31) color
setting
Off
1-255 1-255 1-255 RGB/strobe
2 (32-63)
dim mode
0-15 0-15 0-15
0-255
Adjust
speed
(32-63)
dim mode
No output
16-255 16-255 16-255 selecting color
and strobe to
change speed
3 (64-95)
light mode
0-15 0-15 0-15 (64-95)
light mode
selecting color
and strobe to
change speed
16-255 16-255 16-255
4 (96-127)
light & dim
mode
0-15 0-15 0-15 (96-127)
light & dim
mode
light & dim mode
selecting color
and strobe to
change speed
16-255 16-255 16-255
5 (128-159)
mix color
NA NA NA (128-159)
mix color
mix color adjust
mix color speed
6 (160-191)
3 colors strobe
(192-223)
7 colors strobe
NA NA NA (160-191)
3 colors strobe
(192-223)
7 colors strobe
3/7 colors strobe
adjust strobe
speed
7
8 (224-255)
audio mode
NA NA NA NA (224-255)
audio mode
7 colors sound
control
9 (0-255) NA NA NA NA 1-255
Macro
mode
16-255
strobe
(0-255) NA macro mode
32 colors
4 STAGE PAK DMX Set UP
Due to fog residue, smoke, and dust cleaning the internal and external optical
lenses and mirror should be carried out periodically to optimize light output.
Cleaning frequency depends on the environment in which the xture opera-
tes (I.e. smoke, fog residue, dust, dew). In heavy club use we recommend
cleaning on a monthly basis. Periodic cleaning will ensure longevity, and crisp
output.
1. Use normal glass cleaner and a soft cloth to wipe down the outside
casing.
2. Always be sure to dry all parts completely before plugging the unit back in.
4 STAGE PAK Cleaning
Listed below are a few common problems that you may encounter, with solu-
tions.
No light output from the unit;
1. Be sure you have connected your unit into a standard wall outlet.
2. Be sure the external fuse has not blown. The fuse is located at the rear of
the unit.
3. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound. Tap- ping
on the microphone, quiet or high pitched sounds may not activate the unit.
2. Check the Mic setting. It may be set to a lower sensitivity setting.
4 STAGE PAK Trouble Shooting
87
To Next Page
Loading...
