EasyManua.ls Logo

aermotor FHSN-100 - User Manual

aermotor FHSN-100
36 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Shallow Well Jet Pump
INSTALLATION AND OPERATION MANUAL
Model FHSN-100 Single Stage
1 H.P.
60 Cycle
Single Phase Installations
Owner’s Record
Pump Model:
Pump Serial No.:
Pump Date Code:
Motor H.P. Voltage Phase
Date of Installation:
Owner:
Installer:
Installer Phone Number:
AERMOTOR
293 Wright St., Delavan, WI 53115
1-262-728-9181
©2008 AE376 (Rev. 2/20/08)

Table of Contents

Questions and Answers

  • M
    Mark WellsAug 10, 2025
    What to do if my aermotor Water Pump motor will not run?
    • T
      Taylor HowardAug 10, 2025
      If your Aermotor Water Pump motor isn't running, here are a few things to check: * Ensure the disconnect switch is on. * Replace any blown fuses or reset tripped circuit breakers. * If the starting switch is defective, disconnect the power and replace it. * Check all wiring at the motor, ensuring connections are tight and correct. * Also, disconnect power and clean the pressure switch contacts with an emery board or nail file.
  • A
    Amanda DavisAug 15, 2025
    Why does my aermotor FHSN-100 deliver water but not shut off or cycle too frequently?
    • W
      whitecharlesAug 15, 2025
      If your Aermotor Water Pump is running but not shutting off, or if it cycles too frequently, consider the following: * Disconnect power and adjust or replace the pressure switch if it's out of adjustment or the contacts are welded together. * Ensure all faucets are completely closed. * Clean any clogs from the venturi, nozzle, or impeller. * Drain the tank to the air volume control port if the standard pressure tank is waterlogged. * Check all pipe connections for leaks. * Replace any leaking foot valves. * Check the air pressure in the pre-charged tank using a tire pressure gauge at the valve stem. * Check the air valve for leaks using a soapy solution and replace the core if needed.
  • A
    Amber ClarkAug 25, 2025
    Why is my aermotor FHSN-100 Water Pump motor running hot and the overload keeps kicking off?
    • T
      thomaskevinAug 26, 2025
      If the Aermotor Water Pump motor runs hot and the overload trips, it could be due to a few reasons: * The motor might be wired incorrectly; refer to the wiring instructions. * The voltage could be too low; check with your power company. * The pump may be cycling too frequently; install heavier wiring if the current wire size is too small.
  • A
    Adam LeachAug 30, 2025
    Why does my aermotor FHSN-100 deliver water, but not to full capacity?
    • B
      Bryan JonesAug 30, 2025
      If your Aermotor Water Pump isn't delivering water to its full capacity, consider the following: * If your well's depth to water is more than 25 feet, a deep well jet might be necessary, as the water level in the well may be lower than estimated. * If steel piping is used, corrosion or liming could be causing excess friction; replace it with plastic pipe where possible, or with new steel pipe. * Ensure the piping isn't too small; use larger piping. * If you have a packed well point, try backflushing it or sinking a new one.
  • K
    Kevin AlexanderSep 3, 2025
    Why is there air spurting from the faucets when using my aermotor Water Pump?
    • S
      Stacy JohnsonSep 3, 2025
      If you're experiencing air spurts from the faucets when using your Aermotor Water Pump, here are some potential causes: * The pump may be picking up prime. Once primed, it should pump solid water without air. * There could be a leak in the suction side of the pump. Check joints for leaks using soapy water. * The well might be gaseous. Consult the factory about installing a sleeve in the well. * Intermittent over-pumping of the well could be drawing the water level down below the foot valve. If possible, lower the foot valve; otherwise, restrict pump discharge.
  • B
    Beverly JacksonNov 19, 2025
    What to do if aermotor Water Pump motor runs but no water is delivered?
    • J
      John ScottNov 19, 2025
      If the motor of your Aermotor Water Pump runs, but no water is delivered, consider these potential issues: For new installations: 1. Re-prime the pump according to the instructions, as improper priming, air leaks, or a leaking foot valve/check valve can prevent water delivery. For installations already in use: 1. Check all connections on the suction line and shaft seal for air leaks. Also check: * Clean the foot valve or strainer if plugged. * Clean the ejector or impeller if plugged. * Replace the check valve or foot valve if stuck shut. * Thaw pipes if frozen. * Raise the foot valve and/or strainer above the bottom of the water source if buried in sand or mud. * Consider a deep well jet package if the water level is too low for a shallow well setup (over 25 ft. to wat...

aermotor FHSN-100 Specifications

General IconGeneral
ModelFHSN-100
CategoryWater Pump
TypeHand Pump
PowerManual
Suitable Well Casing Size4 inches

Related product manuals