Agilent Technologies 4395A - Page 223

T
o
Save
and Recall
6.
Press the
softkey corresponding
to the
lename label.
T
o
Save
a
Display
Image
to
a
TIFF
File
1.
Press
4
Save
5
N
N
N
N
NN
NN
NN
NN
NN
NN
NN
N
N
N
N
N
N
N
N
GRAPHICS
.
2.
Select where
to store
the le
by
pressing
either
NN
NN
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
NN
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
STOR DEV
[DISK] (for
a built-in
disk
drive)
or
N
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
STOR
DEV [MEMORY]
(for
a
memory
disk).
3.
Enter
lename
.
Then
press
N
N
N
N
N
N
N
N
N
N
N
N
N
N
DONE
.
Note
A display
image is
saved according
to
the
color
setup
you
have
done
on
the print
setup menu
(
4
Cop
y
5
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
PRINT
SETUP ).
You
can
choose
from
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PRINT:STANDARD (black
and
white),
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
PRINT COLOR
[FIXED]
(color
against
white
background),
and
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PRINT
COLOR
[VARIABLE]
(color
against
black
background).
The
analyzer
saves
a
TIFF le
with an
extension, \
.TIF
"
for
a
DOS
format,
or
a
sux,
\
_T
"
for
a
LIF
format.
If
there
is
a
le
that
has the
same name
you
entered
on
the
disk,
the
error
message
,
\lename
error" will
be
displayed.
T
o
save
the
le
,
use
the
other
lename
to
save
or
purge
the
old
le
.
T
o
purge
a
le
,
press
4
Save
5
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
N
FILE
UTILITIES
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
PURGE
FILE
then
select
the
displayed
lename
by
pressing
the
associated
softkey
.
T
o
Save
Measured
Data
for a
Spreadsheet
1.
Insert
a
DOS
format
disk
into
the
built-in
disk
drive
.
2.
Press
4
Save
5
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
N
N
DATA
ONLY
.
3.
Press
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
SAVE
ASCII
.
4.
Select
the
built-in
disk
drive
as
the
storage
device
by
toggling
to
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
STOR
DEV
[DISK]
.
5.
Enter a
lename.
Then press
N
N
NN
NN
NN
NN
N
N
N
N
DONE .
The
analyzer
saves
an
ASCII
le
with
a
\
.TXT
"
extension.
The
measured
data
is
saved
as
ASCII
text.
Each
value
is
separated
by a
tab
.
When
you
open this le from the spreadsheet software
, specify the le format as the \TEXT with T
AB
delimiter".
Analyzing the Measurement Results 8-21