Agilent Technologies 4395A - Page 224

T
o
Save
and Recall
Figure
8-10.
Reading
Saved
Data
from
Spreadsheet
Software
T
o
Copy
a
File
between
Floppy
Disk
and
Memory
Disk
1.
Press
4
Save
5
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
FILE
UTILITIES
.
2.
Press
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
N
COPY
FILE .
3.
Select
a
storage
device
where
the
le
is
stored by
toggling either
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
NN
N
N
N
N
STOR
DEV
[DISK]
(for
the
build-in
disk
drive) or
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
STOR
DEV
[MEMORY] (for
the memory
disk).
4.
Search
for
the
lename
you
want
to
recall
(the
les
are
listed
on
the
softkey
label).
5.
If
a
target
le
is
not
listed
on
the
softkey labels
,
turn
the
label
page
by
pressing
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
N
N
PREV FILES
or
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
N
N
NEXT FILES
.
6.
Press
the
softkey
corresponding
to the
lename
label.
7.
Enter
the
lename
of
the target
le.
8.
Select
the
target
storage
device
by
toggling
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
STOR
DEV
[DISK]
or
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
N
[MEMORY]
.
9.
Press
N
NN
NN
N
N
N
N
N
N
N
N
N
DONE
to
copy
the
le
.
Y
ou
cannot
copy
a
le
between
the
LIF
and
DOS
formats.
When you
want to
copy a
le
on
a
DOS
formatted
disk
to
the
memory
disk,
you
must
initialize
the memory
disk to
the DOS
format.
To Initialize
a Disk for Use
Note
Initializing the disk erases all data on the disk.
The 4395A can initialize a 1.44 MB 3.5 inch exible disk only
.
1. V
erify that the disk is
not write protected.
2. Insert the disk.
3. Press 4
Save
5 .
4.
Choose
NNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNN
FILE UTILITIES .
5.
Choose
NNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNN
INITIALIZE DISK .
8-22 Analyzing the Measurement Results