Agilent Technologies 4395A - Page 468

Front
P
anel
K
ey
Description
4
Cal
5
Continued
Response standard
menu
?
?
??
??
??
??
??
?
SHORT Measures
SHORT
standard of
7mm
or 3.5
mm cal
kit for
the response
calibration.
?
??
??
??
?
?
?
?
?
OPEN Measures OPEN
standard of
7mm
or
3.5
mm
cal
kit
for
the
response
calibration.
?
?
?
?
?
?
?
?
?
?
?
?
THRU Measures
THRU
standard
of
7
mm
or
3.5
mm
cal
kit
for
the
response
calibration.
?
?
?
?
?
??
??
??
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
DONE:RESPONSE Completes
the
response
calibration
and
computes and
stores the
error coecients
.The
correction
menu is
displayed
with
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
??
??
??
?
?
?
?
?
?
?
CORRECTION ON
.
?
?
?
?
?
?
?
?
?
??
??
??
??
?
?
SHORT[M] Measures
SHORT
standard
of
type-N
cal
kits
connected
to
the type-N
male test
port connector
for
the response
calibration.
??
??
??
?
[M] indicates
that the
test port
connector
is
male
,
it
does
not
indicate
the
connector
type
of
the standard.
?
?
?
?
?
??
??
??
??
?
?
?
?
?
SHORT[F] Measures
SHORT
standard
of
type-N
cal
kits connected
to the
type-N female
test
port
connector
for
the
response
calibration.
?
?
?
?
?
?
[F]
indicates
that
the
test
port
connector
is
female
,
it
does
not
indicate
the connector
type of
the standard.
?
?
?
?
?
??
??
??
?
?
?
?
?
?
OPEN[M] Measures
OPEN
standard
of
type-N
cal kits
connected to
the type-N
male
test
port
connector
for
the
response
calibration.
?
?
?
?
?
?
?
[M]
indicates
that
the
test
port
connector
is
male
,
it
does
not
indicate
the connector
type
of
the
standard.calibration.
?
?
?
?
?
?
?
??
?
?
?
?
?
?
?
OPEN[F] Measures
OPEN
standard
of
type-N
cal
kits
connected to
the
type-N
female
test
port
connector
for
the
response
calibration.
?
?
?
?
?
?
[F]
indicates
that
the
test
port
connector
is
female
,
it
does
not
indicate
the
connector
type
of
the
standard.
?
?
?
?
?
?
?
?
??
??
THRU Measures
THRU
standard
of
type-N
cal
kits
for
the response
calibration.
??
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
??
??
??
?
?
?
DONE:RESPONSE Completes the
response
calibration
and
computes
and
stores
the
error
coecients
.
The
correction
menu
is
displayed
with
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
??
?
?
?
?
?
?
?
?
?
?
?
CORRECTION
ON
.
?
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
?
dened std
1
These softkeys
measure
the
standard
dened
by
the
user
for
the
response
calibration.
When
only
one
standard
is
assigned
to the
response
calibration,
this
softkey
menu
is
not
displayed
and
the
standard is
measured
immediately
.
?
?
?
?
?
?
?
?
?
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
dened
std
2
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
?
?
?
?
?
?
?
?
?
?
dened
std
3
?
?
?
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
dened
std
4
?
?
?
?
?
?
?
?
??
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
dened
std
5
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
??
?
?
?
?
?
?
?
?
?
dened
std
6
?
??
??
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
?
dened
std 7
?
?
?
?
?
?
?
??
??
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
DONE:RESPONSE Completes
the
response
calibration
and
computes
and stores
the error
coecients.
The
correction
menu
is
displayed
with
?
?
?
?
?
?
?
?
?
?
??
??
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
CORRECTION
ON
.
B-20 Softkey Reference