Agilent Technologies 4395A - Page 469

Front
P
anel
K
ey
Description
4
Cal
5
Continued
OPEN standard
menu
??
??
??
??
??
??
?
?
?
?
?
OPEN[M] Measures OPEN
standard of
type-N cal
kits connected
to the
type-N male
test
port
connector
for
the
response
calibration.
?
?
?
?
?
?
?
[M]
indicates
that
the
test
port
connector
is
male
,
it
does
not indicate
the
connector type
of
the
standard.
?
??
??
??
?
?
?
?
?
?
?
?
?
OPEN[F] Measures
OPEN standard
of type-N
cal
kits
connected
to
the
type-N
female
test
port
connector
for
the
response
calibration.
?
?
?
?
?
?
[F]
indicates
that
the
test
port
connector
is
female
,
it
does not
indicate
the
connector
type
of
the
standard.
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
??
?
DONE:OPEN Completes
the
OPEN
calibration
and
computes
and
stores
the
error
coecients
.
The
correction
menu
is
displayed
with
?
?
?
?
?
?
??
??
??
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
?
CORRECTION
ON
.
??
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
??
??
dened std
1
These softkeys
measure the
standard
dened
by
the
user
for
the
OPEN
calibration.
When
only
one
standard is
assigned
to
the
OPEN
calibration,
this
softkey
menu
is
not
displayed
and
the
standard
is measured
immediately.
?
??
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
?
dened std
2
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
??
??
?
?
?
?
dened
std
3
?
?
?
?
?
?
?
??
??
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
dened
std
4
?
?
?
??
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
dened
std
5
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
?
dened
std
6
?
?
?
?
?
?
?
?
?
?
?
?
?
??
??
??
?
?
?
?
?
?
?
?
dened
std
7
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
??
?
DONE:OPEN Completes
the
OPEN
calibration
and
computes
and
stores
the
error
coecients
.
The
correction
menu is
displayed
with
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
??
?
?
?
?
?
?
?
CORRECTION ON
.
SHORT
standard
menu
?
?
??
??
?
?
?
?
?
?
?
?
?
?
?
?
?
SHORT[M] Measures
SHORT
standard
of
type-N cal
kits
connected
to
the
type-N
male
test
port
connector
for
the
response
calibration.
?
?
?
?
?
?
?
[M]
indicates
that
the
test
port
connector
is male
,
it
does
not
indicate
the
connector
type
of
the
standard.
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
SHORT[F] Measures
SHORT
standard
of
type-N
cal
kits
connected
to
the
type-N
female
test
port
connector
for
the
response
calibration.
?
?
?
?
?
?
[F]
indicates
that
the
test
port
connector
is
female
,
it
does
not
indicate
the
connector
type
of
the
standard.
?
?
?
?
?
?
?
?
?
?
?
?
?
??
??
??
?
?
?
?
?
?
DONE:SHORT Completes
the
SHORT
calibration
and
computes
and
stores
the
error
coecients
.
The correction
menu
is
displayed
with
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
??
??
?
?
?
?
?
?
?
?
?
?
?
?
CORRECTION
ON
.
?
?
??
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
??
??
??
dened
std 1
These
softkeys measure
the
standard
dened
by
the
user
for
the
SHORT
calibration.
When
only
one
standard is
assigned to
the SHORT
calibration, this
softkey menu
is
not
displayed
and
the
standard
is
measured
immediately
.
?
?????????
?????????????????
dened std 2
???????????
????????????????
dened std 3
?
??????????????????????
????
dened std 4
????????????????????????
???
dened std 5
?
??????????
????????????????
dened std 6
????????????
???????????????
dened std 7
?
???????????????????????
?
DONE:SHORT Completes the SHORT calibration and computes and stores the error coecients
. The correction
menu is displayed with
?
?????????????????????????????????
CORRECTION ON .
Softkey Reference B-21