Need help?Do you have a question about the Aim MyChron5 660 and is the answer not in the manual?
Guide for physically mounting the MyChron5 660 unit using a bracket.
Instructions for connecting the RPM wire to the dragster's ignition switch.
Details on mounting the EGT thermocouple in the exhaust header pipe.
Steps for installing the cylinder head thermocouple, often near the spark plug.
Procedure for mounting the speed sensor and phonic wheel on the jackshaft.
Detailed instructions for connecting various sensors and the CAN expansion module.
Information on the rechargeable battery and charging process.
Automated setup process for language, temperature, and speed units.
Explains the icons and options available in the main configuration menu.
How to adjust backlight color and night vision mode for the display.
Access to main device functions like Drive Setup, RPM Setup, and more.
Configure tire rollout, drive gear, and recording time for speed calculation.
Set the full-scale RPM range and RPM factor for accurate readings.
Select the preferred unit of measure for temperature (Fahrenheit or Celsius).
Configure alarm LEDs for temperature thresholds and blinking frequency.
View device serial number, firmware, and boot version.
Manage and reset the four engine pass counters for tracking runs.
Configure time zone, time format, daylight saving, and date format.
Set up and manage the device's Wi-Fi connection and modes.
Select the display language for the MyChron5 660.
Accessing the initial setup wizard for device configuration.
Procedure to clear all stored data and settings from the device.
Configuring the device to act as a Wi-Fi access point for direct PC connection.
Connecting the device to an existing Wi-Fi network for broader communication.
Step-by-step guide to setting up the device as a Wi-Fi Access Point.
Steps to connect the device to an existing Wi-Fi network (WLAN).
Example configuration for a WLAN including AiM devices and a PC.
Recommendations for network setup to optimize AiM device performance.
Steps to resolve common issues with Wi-Fi connectivity to the device.
Guidance for Mac users running RaceStudio3 on a virtualized Windows OS.
Addressing delays or failures in displaying connected devices in Race Studio 3.
Guide for physically mounting the MyChron5 660 unit using a bracket.
Instructions for connecting the RPM wire to the dragster's ignition switch.
Details on mounting the EGT thermocouple in the exhaust header pipe.
Steps for installing the cylinder head thermocouple, often near the spark plug.
Procedure for mounting the speed sensor and phonic wheel on the jackshaft.
Detailed instructions for connecting various sensors and the CAN expansion module.
Information on the rechargeable battery and charging process.
Automated setup process for language, temperature, and speed units.
Explains the icons and options available in the main configuration menu.
How to adjust backlight color and night vision mode for the display.
Access to main device functions like Drive Setup, RPM Setup, and more.
Configure tire rollout, drive gear, and recording time for speed calculation.
Set the full-scale RPM range and RPM factor for accurate readings.
Select the preferred unit of measure for temperature (Fahrenheit or Celsius).
Configure alarm LEDs for temperature thresholds and blinking frequency.
View device serial number, firmware, and boot version.
Manage and reset the four engine pass counters for tracking runs.
Configure time zone, time format, daylight saving, and date format.
Set up and manage the device's Wi-Fi connection and modes.
Select the display language for the MyChron5 660.
Accessing the initial setup wizard for device configuration.
Procedure to clear all stored data and settings from the device.
Configuring the device to act as a Wi-Fi access point for direct PC connection.
Connecting the device to an existing Wi-Fi network for broader communication.
Step-by-step guide to setting up the device as a Wi-Fi Access Point.
Steps to connect the device to an existing Wi-Fi network (WLAN).
Example configuration for a WLAN including AiM devices and a PC.
Recommendations for network setup to optimize AiM device performance.
Steps to resolve common issues with Wi-Fi connectivity to the device.
Guidance for Mac users running RaceStudio3 on a virtualized Windows OS.
Addressing delays or failures in displaying connected devices in Race Studio 3.
General| Backlight | Yes |
|---|---|
| Operating Temperature | -10°C to +60°C |
| RPM Input | Yes |
| Gear Indicator | Yes |
| Expandable | Yes |
| Waterproof | Yes |
| Shift Light | Yes |
| Lambda Input | Yes |
| Data Download | USB |
| Connectivity | USB |
To Next Page
