What to do if AirSep Medical Equipment FreeStyle has rapid alarm condition, and the yellow BATT light illuminates intermittently, and FreeStyle shuts down?
If your AirSep Medical Equipment FreeStyle is experiencing a rapid alarm, the yellow BATT light is flashing, and the unit shuts down, it indicates that the battery voltage is too low. Immediately connect the unit to a DC or AC outlet, or use the optional AirBelt.
Why does my AirSep Medical Equipment FreeStyle have intermittent alarm condition, and the yellow batt light illuminates intermittently?
If your AirSep Medical Equipment FreeStyle has an intermittent alarm and the yellow BATT light is flashing, it means the battery needs charging. Connect the unit to a DC or AC outlet within 2 minutes, or connect it to the optional AirBelt.
What to do if AirSep Medical Equipment FreeStyle has intermittent alarm condition, and the red alarm light illuminates intermittently?
If your AirSep Medical Equipment FreeStyle has an intermittent alarm and the red alarm light flashes, it means that your breathing rate has exceeded the capacity of the unit. In this case, switch to another source of oxygen and contact your Equipment Provider.
What to do if AirSep Medical Equipment has continuous alarm?
If your AirSep Medical Equipment FreeStyle unit sounds a continuous alarm and the red alarm light stays on, it means the device hasn't detected a breath for 15 minutes. Check the cannula connection, make sure the tubing isn't kinked, and ensure the cannula is properly positioned so you're breathing through your nose. If you breathe through your mouth, a chin strap might help.
How to fix AirSep Medical Equipment FreeStyle that does not operate when a pulse flow selection button is pressed?
If your AirSep Medical Equipment FreeStyle unit does not operate when you press a pulse flow selection button, the battery might be discharged. Try powering the unit through the DC outlet or an AC outlet. If this doesn't resolve the issue, it may indicate a malfunction, and you should contact your Equipment Provider and switch to a reserve oxygen supply.
What causes delay in recharging internal battery of AirSep?
A delay in recharging the internal battery of your AirSep unit can occur if the internal battery exceeds its charging temperature. The unit can still be operated, but charging may not resume until the battery temperature decreases.
How to troubleshoot AirSep FreeStyle if it does not operate?
If your AirSep FreeStyle doesn't operate when you press a pulse flow selection button, it could be due to a discharged battery or a malfunction. Try powering the unit through a DC or AC outlet.
What to do if AirSep FreeStyle has an intermittent alarm and yellow light?
If your AirSep FreeStyle has an intermittent alarm and the yellow BATT light flashes, it means the battery needs charging. Connect it to a DC or AC outlet within 2 minutes, or connect to the optional AirBelt.
What to do if AirSep FreeStyle has an intermittent alarm and red light?
If your AirSep FreeStyle has an intermittent alarm and the red light flashes, it means your breathing rate has exceeded the unit's capacity. Reduce your activity, then turn the unit off and back on to reset it.
Why AirSep FreeStyle won't start on battery power?
If your AirSep FreeStyle won't start on battery power, it might be too hot or cold from being left outdoors, like in a car. Let it reach normal operating temperature, which could take a few minutes if it was exposed to extreme temperatures. You may temporarily connect your AC or DC power supply to the unit’s power inlet and power source, as needed, to reset the unit’s internal battery.
Outlines the duties of equipment providers for handling, operation, and maintenance.
Explains safety symbols (Warning, Caution, Note) and their meanings.
Lists and defines various symbols used in the manual and on the equipment.
Details the warranty terms and conditions for the FreeStyle Oxygen Concentrator.
Provides technical specifications for the FreeStyle unit, including dimensions, power, and performance.
Details the electrical and safety classifications of the FreeStyle equipment.
Explains how the FreeStyle oxygen concentrator works to produce oxygen.
Procedure to test the FreeStyle unit after manufacture for shipping damage.
Covers startup, battery status, low/discharged battery, charging, full charge, disconnect, performance, capacity, and general malfunction alarms.
Procedure to test and verify the oxygen output concentration of the FreeStyle unit.
Guidance on unit operation, connecting power, and using the optional AirBelt battery.
Routine maintenance tasks for patients, including filter cleaning and indicator checks.
Overview of maintenance, including filter care, filter replacement, compressor servicing, and record keeping.
Procedures for infection control and cleaning the unit for new patient use.
Overview of components and instructions for removing unit housing.
Step-by-step guide for replacing the internal battery pack.
Procedure for safely removing the PSA system assembly from the unit.
Detailed steps for removing and installing the compressor assembly.
Instructions for replacing manifolds, solenoid valves, and adsorbent beds.
Method for measuring system pressure using a test kit.
Explains hour meter functionality, replacement, and related indicators.
Procedures for replacing circuit boards, control panels, and the fan.
Illustrates normal operating pressure ranges and fault conditions for the unit.
Initial steps to isolate malfunctions before consulting the troubleshooting chart.
A detailed chart listing problems, possible causes, and solutions for unit malfunctions.
Lists essential tools for performing service and maintenance on the FreeStyle unit.
Provides diagrams showing the internal components of the unit.
General| Audible Alarm | Yes |
|---|---|
| Operating Temperature | 41°F to 104°F (5°C to 40°C) |
| Power | 100-240 VAC, 50/60 Hz |
| Operating Humidity | 15% to 95% (non-condensing) |
| Oxygen Concentration | 90% (+5.5% / -3%) at all settings |
| Weight | 4.8 lbs (2.2 kg) with battery |
To Next Page
