AIRTRONICS MT-4s User Manual

1
T R


AIRTRONICS MT-4s Specifications

General

Channels	4
Frequency	2.4GHz
Display	LCD
Battery Type	4x AA
Servo Compatibility	Digital

Summary

SAFETY

FCC COMPLIANCE STATEMENT

RF Exposure Statement

Statement regarding compliance with FCC RF exposure guidelines.

TRANSMITTER PRECAUTIONS

RECEIVER PRECAUTIONS

SYSTEM FEATURES

RECEIVER OVERVIEW DIAGRAMS

Receiver Connections and Mounting

Details on connecting and mounting the receiver and its components.

TRANSMITTER SAFETY ALARMS AND LED CONDITION INDICATORS

Audible Warning Alarms

Details the various audible alarms for transmitter conditions.

TRANSMITTER BATTERY OPTIONS

ALKALINE BATTERY INSTALLATION

Instructions for installing AA alkaline batteries into the transmitter.

THROTTLE TRIGGER POSITION ADJUSTMENT

THROTTLE TRIGGER ANGLE ADJUSTMENT

TOP SCREEN AND TELEMETRY SCREEN OVERVIEW

TELEMETRY Screen

Explains the telemetry data displayed on the transmitter screen.

BINDING THE TRANSMITTER AND RECEIVER

PROGRAMMING MENUS OVERVIEW

01.CH-SET (CHANNEL SET)

Allows common programming changes for all four channels in one menu.

03.EPA (END POINT ADJUSTMENT)

05.SPEED (SERVO SPEED)

06.ALB (ANTI-LOCK BRAKING)

08.AUX1 (AUXILIARY 1 CHANNEL 3 PROGRAMMING)

STEP AUX (Step Auxliary)

Programs Auxiliary 1 servo to move a defined amount when toggled ON/OFF.

09.AUX2 (AUXILIARY 2 CHANNEL 4 PROGRAMMING)

STEP AUX (Step Auxliary)

Programs Auxiliary 2 servo to move a defined amount when toggled ON/OFF.

10.TRIM (TRIM AND SERVO SUB-TRIM)

Adjusting the Servo Sub-Trim Values

Instructions for adjusting servo sub-trim to center servo horns accurately.

11.REV (SERVO REVERSING)

12.TIMER (TRACK TIMERS)

LAP (Lap Timer)

Function to measure and record times for up to 99 laps.

INT (Interval Timer)

DOWN (Countdown Timer)

13.LAP (LAP TIMES)

14.F/S (FAIL SAFE)

Setting the Fail Safe

Configures servo positions for loss of signal or low transmitter battery.

Setting the Receiver Battery Voltage Fail Safe Function

SYSTEM MENUS OVERVIEW

01.MODEL (MODEL SELECT, NAMING, COPY AND CLEAR)

MODEL SELECT (Model Select)

Allows selection of stored programming data for a specific model.

MODEL COPY (Model Programming Data Copy)

MODEL CLEAR (Model Programming Data Reset)

02.BIND (BINDING, MODULATION TYPE AND SERVO OPERATING MODE)

Changing the Modulation Type

Allows selection of transmitter modulation type to match receiver.

Changing the Servo Operating Mode

Optimizes radio control system to suit servo type for response time.

03.KEY ASSIGN (KEY ASSIGNMENTS)

SWITCH (Push-Button Switch Key Assignments)

Assigns functions to Push-Button Switches Sw1 and Sw2 for ON/OFF control.

TRIM, DIAL AND LEVER (Trim Switch, Rotary Dial and Auxiliary Lever Key Assignments)

05.AUX TYPE (AUXILIARY TYPE)

Changing the Auxiliary Function

Assigns functions to Auxiliary 1 and Auxiliary 2 channels.

06.TH TYPE (THROTTLE TYPE)

Changing the Throttle Type

Changes throttle neutral point proportion for general use or rock crawling.

08.BATTERY (VOLTAGE ALARM)

Changing the Low Voltage Alert Alarm Value

Sets the voltage threshold for the low voltage alert alarm.

Changing the Low Voltage Limit Alarm Value

09.LCD (LCD CONTRAST AND BACKLIGHT OPTIONS)

Changing the LCD Contrast Value

Adjusts the LCD screen contrast for better visibility.

10.TELEMETRY (TELEMETRY DISPLAY OPTIONS)

TEMP1 AND TEMP2 SETTING (Temperature Telemetry Display Options)

Configures temperature display and alert settings for sensors.

Changing the Temperature Unit Value

Changing the Maximum Temperature Value

Changing the Minimum Temperature Value

VOLT SETTING (Receiver Battery Voltage Telemetry Display Options)

Changing the Maximum Voltage Value

Sets the maximum receiver battery voltage displayed on screen.

Changing the Alert Voltage Value

RPM SETTING (RPM and Speed Telemetry Display Options)

Changing the RPM Unit Value

Sets display units for RPM/Speed (RPM, MPH, or KM/H).

Changing the Maximum RPM/Speed Value

Calibrating the RPM Sensor - Changing the 10Count Distance Value

TELEMETRY SETTING (Telemetry ON/OFF and Telemetry Log Options)

Changing the Telemetry Log Step Value

TE-CLEAR (Telemetry Clear Function)

11.VR ADJUST (VARIABLE RATE ADJUSTMENT)

Calibrating Control Operation

Calibrates steering wheel, throttle trigger, and auxiliary lever endpoints and neutrals.

TELEMETRY CONNECTIONS AND MOUNTING

Plugging the Telemetry Sensors into the Receiver

Instructions for connecting telemetry sensors to the receiver.

Mounting the RPM Sensor

Mounting the Temperature Sensor

TROUBLESHOOTING GUIDE

GLOSSARY OF TERMS