AIRTRONICS MT-S - User Manual

Questions and Answers

V
vbassNov 24, 2025
What to do if AIRTRONICS Remote Control transmitter will not bind to receiver?
- Q
  qgonzalesNov 24, 2025
  If your AIRTRONICS Remote Control transmitter isn't binding to the receiver, consider the following: * The Modulation Type might be incorrect. Change the Modulation Type to match the receiver. * Too much time might have elapsed after pressing the receiver Bind Button. Quickly press the ENTER key in the BIND menu after releasing the receiver Bind Button. * You might be attempting to Bind an incompatible receiver. Use only Airtronics or Sanwa 2.4GHz FH3, FH4 or FH4T surface receivers. * If you're using an Electronic Speed Control (ESC), disconnect it and use a dry cell battery for the Binding procedure, then reconnect the ESC after Binding. * The receiver batteries might be dead. Replace or recharge the receiver batteries. * You might be using an incorrect Binding procedure. Fol...
R
rwashingtonAug 25, 2025
Why AIRTRONICS MT-S transmitter does not turn on?
- H
  Holly EvansAug 25, 2025
  The AIRTRONICS Remote Control transmitter might not turn on due to several reasons: * The batteries might be installed incorrectly. Reinstall them, making sure to observe the correct polarity. * The battery tray might not be plugged in. Ensure that the battery tray is properly plugged in. * The transmitter batteries might be dead. Replace or recharge the transmitter batteries.
J
josephsloanAug 26, 2025
Why AIRTRONICS MT-S audible alarm beeps continuously?
- C
  Cody PowellAug 27, 2025
  The continuous beeping from your AIRTRONICS Remote Control audible alarm could be due to: * Low transmitter battery voltage. Replace or recharge the transmitter batteries. * The transmitter being left ON for 10 minutes or more without control input. Move the Steering Wheel or Throttle Trigger, or press any key to clear the alarm and continue operation. * Transmitter battery voltage being too high. Use a transmitter battery whose voltage is 9.6 volts or less when fully charged.
M
Mark ShawAug 27, 2025
Why AIRTRONICS MT-S servo movement is slow?
- S
  shawnjamesAug 27, 2025
  Slow servo movement in your AIRTRONICS Remote Control can be attributed to: * Low receiver battery voltage. Replace or recharge the receiver batteries. * Control linkages binding. Adjust control linkages to operate smoothly. * Using a negative Servo Speed value. Increase Servo Speed value.
J
Jeffrey MartinezAug 28, 2025
How to improve AIRTRONICS MT-S transmitting range?
- A
  Anna EdwardsAug 29, 2025
  If you're experiencing inadequate transmitting range with your AIRTRONICS Remote Control, consider the following: * Low transmitter battery voltage. Replace or recharge the transmitter batteries. * Low receiver battery voltage. Replace or recharge the receiver batteries. * Incorrect receiver mounting. Mount the receiver exactly as recommended.
C
Christopher HutchinsonSep 16, 2025
Why AIRTRONICS MT-S Remote Control servo(s) and/or ESC don't operate at all or operate erratically?
- J
  Jeffrey VasquezSep 16, 2025
  If the servo(s) and/or ESC don't operate at all or operate erratically on your AIRTRONICS Remote Control, it's because you're using an incorrect Channel Response Mode setting. Use the correct Channel Response Mode setting based on the type of servos and/or ESC you're using.
S
Samantha SalasSep 14, 2025
Why AIRTRONICS MT-S Remote Control throttle servo pulsates?
- E
  Elizabeth JonesSep 14, 2025
  If the throttle servo pulsates on your AIRTRONICS Remote Control, it's because the ABS function is turned ON. This is normal under Braking with the ABS function ON.
R
richard87Sep 15, 2025
Why there is no key-press or Timer function sounds on AIRTRONICS MT-S?
- C
  Courtney CookSep 15, 2025
  If there are no key-press or Timer function sounds on your AIRTRONICS Remote Control, it's because the Audible Key Tones are Muted. Increase the Volume setting in the BUZZER menu.
H
heathermendezSep 6, 2025
Why AIRTRONICS Remote Control servo moves too much or not enough when Trim Switch is pressed?
- C
  Connie ReedSep 6, 2025
  If the servo moves too much or not enough when the Trim Switch is pressed on your AIRTRONICS Remote Control, it's because the Trim Step resolution requires adjustment. Adjust the Trim Step resolution.
L
Lawrence LuceroSep 4, 2025
Why AIRTRONICS MT-S Remote Control model seems extremely sensitive to control input?
- M
  Mr. Joe MoodySep 4, 2025
  If your AIRTRONICS Remote Control model seems extremely sensitive to control input: * Dual Rate value(s) might be set too high. Decrease Dual Rate value(s). * There might be no or positive ARC value programmed. Program a negative ARC value.