What to do if my Airwell GCN 9 R410A does not respond to remote control?
If the Airwell Air Conditioner unit does not respond to the remote control command, it could be that the remote control command didn't reach the indoor unit. First, check the remote control batteries. If the batteries are OK, check the display and display wiring. If those are OK, replace the PCB.
How to reset filter light on Airwell GCN 9 R410A Air Conditioner?
When the filter LED comes ON on your Airwell Air Conditioner after 512 hours of operation, it means the air filter is clogged. Replace the air filter and then press the RESET button.
Why is my Airwell GCN 9 R410A working in the wrong mode?
If the Airwell Air Conditioner unit works in the wrong mode (cooling instead of heating, or heating instead of cooling), the issue could stem from the electronics or the power connection to the RV. First, check the RV power connections. If those are OK, test the RV operation using a direct 230 VAC power supply. If it then works correctly, replace the outdoor controller.
What to do if Airwell Air Conditioner compressor is on but outdoor fan is not working?
If the Airwell Air Conditioner's compressor is running but the outdoor fan isn't working, it could be due to a problem with the outdoor electronics or the outdoor fan capacitor. To troubleshoot, switch the unit to COOL mode, HIGH speed with 16 degrees set point (in summer) or HEAT mode high speed with 30 degrees set point (in winter). Check that the power supply to the motor is higher than 130 VAC. If it is OK, replace the capacitor; if not, replace the controller.
Why Airwell GCN 9 R410A indoor fan works when unit is off?
If the indoor fan of your Airwell Air Conditioner is running even when the unit is OFF, and you can't change the fan speed with the remote control, it's likely a PCB problem. To fix this, replace the controller.
Why is my Airwell GCN 9 R410A compressor motor noisy?
If the compressor motor in your Airwell Air Conditioner is noisy and there's no suction, it could be due to the wrong phase order to the compressor. Check the compressor phase order to resolve this.
Why Airwell Air Conditioner indoor fan does not start?
If the indoor fan of your Airwell Air Conditioner isn't starting, but the louvers are open and the Green LED is lit, it could be due to a couple of reasons. First, if the unit is in HEAT MODE and the coil isn't warm yet, change to COOL MODE to check if the fan starts. Alternatively, there might be a problem with the PCB or capacitor. To check this, change to HIGH speed and see if the power supply to the motor is higher than 130 VAC. If it is OK, replace the capacitor; if not, replace the controller.
Why is my Airwell GCN 9 R410A leaking water inside?
If water is leaking from the indoor unit of your Airwell Air Conditioner, it's likely that the drainage tube is blocked. Check the drainage tube and clear any blockages.
Why Airwell Air Conditioner power supply indicator does not light up?
If the power supply indicator (Red LED) on your Airwell Air Conditioner isn't lighting up, it indicates there's no power supply. Check the power supply first. If the power supply is OK, check the display and display wiring. If those are OK, replace the PCB.
What to do if Airwell GCN 9 R410A responds to remote but operate indicator does not light up?
If the Airwell Air Conditioner unit responds to remote control commands, but the operate indicator (Green LED) doesn't light up, it indicates an issue with the display PCB. Replace the display PCB to resolve this.
General| Brand | Airwell |
|---|---|
| Model | GCN 9 R410A |
| Category | Air Conditioner |
| Language | English |
Detailed technical data for the CN-9 indoor and GCN 9 R410A outdoor units.
Detailed technical data for the CN-12 indoor and GCN 12 R410A outdoor units.
Detailed technical data for the CN-18 indoor and ONG3-17 R410A outdoor units.
Diagrams and table showing the outline dimensions for indoor units CN 9, CN 12, and CN 18.
Diagrams showing the outline dimensions for outdoor unit GCN 9/12 R410A.
Diagrams showing the outline dimensions for outdoor unit ONG3-17 R410A.
Detailed performance data for CN 9 / GCN 9 R410A unit.
Detailed performance data for CN 12 / GCN 12 R410A unit.
Detailed performance data for CN 18 / ONG3-17 R410A unit.
Table showing cooling capacity (kW) under various entering air conditions.
Table showing heating capacity (kW) under various entering air conditions.
Graphs illustrating discharge and suction pressure vs. outdoor temperature.
Discharge and suction pressure curves for cooling mode.
Introduction to electronic control, jumper settings, and model selection.
Explains compressor, fan, and thermistor operations and protections.
Details general cooling mode, cooling with autofan, and specific operations.
Details general heating mode, RC/SH group heating, and autofan operations.
Describes automatic mode switching and operations for different groups.
Explains dry mode operation for ST/RC and SH groups.
Covers various protections like coil defrost, high pressure, and pump operations.
Provides critical safety warnings and precautions for installation and operation.
Step-by-step guide for installing the indoor unit and determining ceiling openings.
To Next Page
