Alliance Laundry Systems LWB19A*-1109 series User Manual (English)

Questions and Answers:

B
barnesjonathanAug 19, 2025
Why is my Alliance Laundry Systems LWB19A*-1109 spinning slowly or not at all?
- L
  Lindsey BellAug 19, 2025
  If your Alliance Laundry Systems Washer isn't spinning properly, start by checking if the loading door is completely closed and the safety switch is working. A loose or broken drive belt could also be the culprit, so inspect and replace it if necessary. Additionally, a bind in the water pump might be the cause, requiring a pump replacement. In some cases, the motor overload protector may have cycled; wait a few minutes for it to reset. If issues continue, it may be necessary to test timer continuity, inspect the wiring, or address brake pad issues.
E
Eric AcevedoAug 21, 2025
Why is there no agitation in my Alliance Laundry Systems LWB19A*-1109?
- J
  Joshua VargasAug 21, 2025
  If your Alliance Laundry Systems Washer isn't agitating, first make sure the loading door is closed and the door switch is working correctly. If the washer is in the DELICATE cycle, the timer might be paused for a soak period. If the motor isn't running, that could also be the cause. Check the drive belt for looseness or breakage, and replace it if needed. You might also need to test the pressure switch or inspect the wiring. If these steps don't resolve the issue, the transmission assembly or pump may be inoperative.
M
Melissa WatsonAug 23, 2025
What causes constant spinning in my Alliance Laundry Systems LWB19A*-1109?
- C
  Chelsea CookAug 25, 2025
  If your Alliance Laundry Systems Washer is constantly spinning, the timer might be inoperative, requiring testing for continuity and possible replacement. Also, the washtub should stop spinning within seven seconds after opening the loading door; if it doesn't, the brake pads and brake assembly may need replacement. Check for excessive wear or missing brake pads and replace them as needed. Also, the lid switch might be inoperative, requiring replacement. Finally, check for shorted or incorrect wiring.
P
pandersonAug 26, 2025
What causes constant agitation in my Alliance Laundry Systems LWB19A*-1109 Washer?
- Y
  yuthomasAug 26, 2025
  If your Alliance Laundry Systems Washer is constantly agitating, the timer might be inoperative, requiring testing for continuity and possible replacement. Also, check for shorted or incorrect wiring, which can cause continuous agitation. An inoperative transmission assembly can also lead to this issue, requiring repair or replacement.
E
emooreAug 28, 2025
What to do if the motor does not run on my Alliance Laundry Systems LWB19A*-1109?
- J
  Joseph LucasAug 28, 2025
  If your Alliance Laundry Systems Washer's motor isn't running, there might be a few reasons. First, check that the power cord is plugged in and that there are no blown fuses or tripped circuit breakers in your laundry room. Also, ensure the loading door is completely closed. If these aren't the issue, the timer might be set incorrectly, so try resetting it or selecting a different cycle. If problems persist, further diagnosis, possibly involving a wiring diagram, may be needed to check the timer, start switch, windings, or for any binding in the motor bearings or pump.
X
xsantanaAug 30, 2025
How to reduce excessive vibration in my Alliance Laundry Systems LWB19A*-1109 Washer?
- S
  Susan LarsonAug 30, 2025
  If your Alliance Laundry Systems Washer is vibrating excessively, start by ensuring the washer is properly leveled using the leveling legs. An unbalanced load in the tub can also cause this, so stop the washer, redistribute the load, and restart. Check for broken or disconnected centering springs and ensure they are connected or replaced. The floor beneath the washer should also be firm; if it's weak or spongy, consider relocating the washer or supporting the floor. Also inspect cabinet screws to ensure that they are correct and tight.
K
Kenneth StarkSep 2, 2025
Why does the timer not advance on my Alliance Laundry Systems LWB19A*-1109?
- M
  Megan LeeSep 2, 2025
  If your Alliance Laundry Systems Washer's timer isn't advancing, it could be due to a few reasons. The timer is designed to pause during fill periods, especially in delicate cycles, so allow it to complete. An open loading door will also stop the timer, so ensure it's closed. If the washer isn't filling, the timer will pause until the pressure switch is satisfied. Also, the timer is designed to pause when going from agitate to spin, so allow time for the timer to go through that step. Check if the circuit breaker has tripped, disconnecting power to the washer, and reset it if necessary.
J
Jennifer PhillipsSep 4, 2025
What to do if water fill does not stop at proper level in Alliance Laundry Systems Washer?
- A
  Ashley HollandSep 4, 2025
  If the water fill in your Alliance Laundry Systems Washer doesn't stop at the correct level, the pressure switch might be inoperative, requiring testing and replacement if needed. An air leak in the pressure hose could also be the cause, so replace the hose. Sediment on the mixing valve diaphragm, a defective diaphragm, or armature binding can also cause this issue, so replace the valve. Additionally, a broken or weak mixing valve armature spring can be the problem, also requiring valve replacement. A siphoning action can also cause this, so install a siphon break kit and ensure an air gap around the drain hose.
C
Christopher MillerSep 6, 2025
Why does my Alliance Laundry Systems LWB19A*-1109 Washer overheat and cycle on the motor thermal protector?
- M
  Matthew HutchinsonSep 6, 2025
  If your Alliance Laundry Systems Washer overheats and cycles on the motor thermal protector, it could be due to several reasons. A tacky belt that doesn't allow proper slip can cause this, so check and replace it if defective. Excessive belt tension can also be a factor, so ensure the idler spring is properly connected. Additionally, a bind in the water pump or binding brake pads can lead to overheating, requiring pump or brake pad replacement. Also, check that components such as bearings, transmission, or motor are able to move freely.
N
Natalie BlackburnSep 8, 2025
Why does my Alliance Laundry Systems LWB19A*-1109 Washer stop in cycle or quit intermittently?
- A
  Alison JordanSep 9, 2025
  If your Alliance Laundry Systems Washer stops mid-cycle or quits after a few loads, a tacky belt preventing proper slip could be the cause, so inspect and replace it if needed. Excessive belt tension might also be the issue, so ensure the idler spring is correctly connected. An inoperative timer can also lead to this problem, requiring testing and possible replacement. Also, the motor overload protector may have cycled; wait a few minutes for it to reset. Finally, check that components such as the brake, transmission or motor can move freely.