Why is my Alpine Spas Hot Tub not heating up?
If your Alpine Spas Hot Tub isn't heating, make sure it's not in rest, away, or sleep mode. Switch it to ready or normal mode. Also, increase the set temperature.
What to do if my Alpine Spas Hot Tub has no power?
If your Alpine Spas Hot Tub has no power, first check that the RCD is turned on. Then, have an electrician check the plug and wire connections.
What to do if my Alpine Spas Hot Tub doesn’t reach set temperature?
If your Alpine Spas Hot Tub doesn’t reach the set temperature, it might be in rest, away, or sleep mode. Change the mode to ready or normal.
Why does the RCD trip on my Alpine Spas Hot Tub?
If your Alpine Spas Hot Tub RCD trips, have an electrician check that the wiring is correct and matches the diagram. It could also be a component failure, so call for service.
How to fix low jet pressure in my Alpine Spas Hot Tub?
If you have low jet pressure in your Alpine Spas Hot Tub, turn the jet face anti-clockwise to open it. If you have a 2-Speed Pump, press the jet button again to enter high speed.
What to do if there is no jet pressure in my Alpine Spas Hot Tub?
If there's no jet pressure in your Alpine Spas Hot Tub, try priming the pump by pressing the jets button on and off 2-3 times in sequence. Also, bleed the pump by loosening the barrel union.
Why are the speakers not working on my Alpine Spas Hot Tub?
If the speakers aren't working on your Alpine Spas Hot Tub, ensure the Bluetooth light is activated when pressing the on button. Also, remove any protective case from your device and try again, as it may be interfering.
How to fix a blank display on my Alpine Spas Hot Tub?
If the display on your Alpine Spas Hot Tub is blank, switch the spa pool off and on again.
Why does my Alpine Spas Hot Tub emit a high pitch ringing noise?
If your Alpine Spas Hot Tub emits a high-pitched ringing noise, check for leaking around the UV chamber and replace the UV bulb if necessary, as this indicates a UV system alarm because the bulb has failed.
Guidance on selecting the best position, ensuring proper drainage, and checking service access for the spa pool.
Steps to prepare the spa pool before filling with water, crucial for startup and warranty.
Detailed steps for filling the spa pool using the grate skimmer type.
Detailed steps for filling the spa pool using the floating weir skimmer type.
Information on electrical requirements, wiring, and powering up the spa pool safely.
Instructions for setting up the spa pool with a 15A electrical supply, including load-shedding details.
Instructions for setting up the spa pool with a 25A or 32A electrical supply, requiring hardwiring.
Instructions for automatically starting the spa pool and the initial heating process.
Essential guide to balancing and sanitizing spa pool water for cleanliness and component protection.
Overview of topside control panel buttons and their functions for operating the spa pool.
Detailed explanation of buttons and features for the SpaNet SV-SMART topside control panel.
Guide to the SpaNet SV-SMART control panel specific to Sierra, Vancouver, and Munro spa pool models.
Guide for the SpaNet SV3-VH topside control panel used with the K2 Spa Pool model.
Details on operating the spa pool, understanding the display, and changing temperature settings.
Understanding and setting programmed filter cycle durations and blocks for water sanitization.
Activating the 20-minute sanitisation cycle to refresh spa water quality and purge plumbing.
Step-by-step guide on operating the external drain valve to safely drain the spa pool water.
A detailed schedule for weekly, monthly, and 3-4 monthly cleaning and maintenance tasks.
General troubleshooting guide for common issues with spa pool displays, power, heating, and jets.
Explanation of diagnostic messages, their causes, and required actions for the topside control panel.
General| Brand | Alpine Spas |
|---|---|
| Model | ALASKA |
| Category | Hot Tub |
| Language | English |
To Next Page