Why is my Alpine Spas Hot Tub not heating up?
If your Alpine Spas Hot Tub isn't heating, make sure it's not in rest, away, or sleep mode. Switch it to ready or normal mode. Also, increase the set temperature.
What to do if my Alpine Spas Hot Tub has no power?
If your Alpine Spas Hot Tub has no power, first check that the RCD is turned on. Then, have an electrician check the plug and wire connections.
What to do if my Alpine Spas Hot Tub doesn’t reach set temperature?
If your Alpine Spas Hot Tub doesn’t reach the set temperature, it might be in rest, away, or sleep mode. Change the mode to ready or normal.
Why does the RCD trip on my Alpine Spas Hot Tub?
If your Alpine Spas Hot Tub RCD trips, have an electrician check that the wiring is correct and matches the diagram. It could also be a component failure, so call for service.
How to fix low jet pressure in my Alpine Spas Hot Tub?
If you have low jet pressure in your Alpine Spas Hot Tub, turn the jet face anti-clockwise to open it. If you have a 2-Speed Pump, press the jet button again to enter high speed.
What to do if there is no jet pressure in my Alpine Spas Hot Tub?
If there's no jet pressure in your Alpine Spas Hot Tub, try priming the pump by pressing the jets button on and off 2-3 times in sequence. Also, bleed the pump by loosening the barrel union.
Why are the speakers not working on my Alpine Spas Hot Tub?
If the speakers aren't working on your Alpine Spas Hot Tub, ensure the Bluetooth light is activated when pressing the on button. Also, remove any protective case from your device and try again, as it may be interfering.
How to fix a blank display on my Alpine Spas Hot Tub?
If the display on your Alpine Spas Hot Tub is blank, switch the spa pool off and on again.
Why does my Alpine Spas Hot Tub emit a high pitch ringing noise?
If your Alpine Spas Hot Tub emits a high-pitched ringing noise, check for leaking around the UV chamber and replace the UV bulb if necessary, as this indicates a UV system alarm because the bulb has failed.
Key safety warnings including supervision, drowning prevention, electrical safety, and temperature guidelines.
Details on required electrical supply, RCD, and disconnect for safe operation.
Cautions regarding electrical shock, self-servicing, and handling damaged electrical components.
Warnings on using the cover, post-exercise use, dizziness, high temperatures, and jet pressure.
Prohibits actions like leaving the spa empty, powering without water, or submerging heads.
Mandates water maintenance, cover security, regular cleaning, draining, filtration, and ventilation.
Essential steps to follow before filling the spa pool to prevent startup issues or warranty voiding.
Warning about potential damage to components if the spa pool is not kept at the minimum required water level.
Guidance on electrical wiring and powering up, emphasizing licensed electrician use.
Details on setting up 15A spa pools, including RCD requirements and factory load-shedding.
Information on setting up 25A or 32A spa pools, requiring dedicated feed and electrician.
Step-by-step instructions for installing filter cartridges in spa pools with floating weir skimmers.
Step-by-step instructions for installing filter cartridges in spa pools with grate skimmers.
Covers the automatic startup sequence, priming mode, and initial heat-up process.
Emphasizes the importance of balancing and sanitizing water to prevent component damage and maintain cleanliness.
Provides an overview of the topside control panel, its functions, and button actions.
Step-by-step guide on operating the external drain valve to drain the spa pool water.
A schedule outlining weekly, monthly, and 3-4 monthly cleaning and maintenance tasks for the spa pool.
A table listing common issues, their possible causes, and solutions for general spa pool problems.
Explanation of diagnostic messages displayed on the topside control panel and required actions.
General| Brand | Alpine Spas |
|---|---|
| Model | MUNRO |
| Category | Hot Tub |
| Language | English |
To Next Page