American Standard AccuLink Platinum 1050 User Manual (English)

Other manuals for American Standard AccuLink Platinum 1050

Manual32 pages

User Guide32 pages

Questions and Answers:

M
Ms. Stephanie MccartyAug 20, 2025
Why is my American Standard Control Unit heating not working?
- D
  danny82Aug 20, 2025
  Your American Standard Control Unit may not be heating because the system mode isn't set to Heat/Auto, or the setpoint is too low. Set the mode to heat and raise the setpoint above the room temperature. It's also possible the minimum off time delay is being enforced; wait 5 minutes and recheck the heating equipment. Finally, the heating system itself may require service, so check and repair the system if needed.
B
Brian CookAug 22, 2025
What to do if my American Standard Control Unit cooling will not turn on?
- K
  Kelly RodriguezAug 22, 2025
  If your American Standard Control Unit cooling won't turn on, first ensure the system mode is set to Cool/Auto and that the setpoint is lower than the room temperature. If that's not the issue, the minimum off time delay might be in effect; wait 5 minutes before rechecking. If problems persist, the cooling system may need professional attention, so check and repair the system.
K
karenbruceAug 25, 2025
How to stop my American Standard Control Unit fan from running constantly?
- M
  monica69Aug 25, 2025
  To stop your American Standard Control Unit fan from running constantly, first check the 1050 Control settings to see if the fan is set to On, Circulate, or Clean mode. If it is, change the setting. If the settings are correct, there may be a failure in the indoor unit, such as a tripped heating limit; check the indoor unit for failures.
C
Christopher BullockAug 26, 2025
Why is my American Standard Control Unit showing heating or cooling but no air is coming out?
- T
  Troy CohenAug 27, 2025
  If your American Standard Control Unit displays heating or cooling but no warm or cool air comes from the registers, there might be a fan delay as the heating or cooling equipment turns on. Wait a minute for blower delays and recheck the registers. If the problem persists, the equipment may not be working properly, so check and repair the system.
S
sandrareedAug 28, 2025
What causes temperature overshoot with my American Standard Control Unit?
- J
  John SinghAug 28, 2025
  Temperature overshoot in your American Standard Control Unit can occur if the heating/cooling equipment is oversized for the current conditions, preventing the 1050 Control from responding fast enough. Compare heat load calculation to the equipment chosen. It can also happen if the 1050 Control is improperly located. Relocate the 1050 Control or use a remote sensor.
J
Joseph BarnettAug 29, 2025
How to fix temperature swings with my American Standard Control Unit?
- J
  Jason DavisAug 29, 2025
  To fix temperature swings with your American Standard Control Unit, first check the location of the 1050 Control for drafts and seal any air leaks behind it. Consider relocating the 1050 Control or applying a remote indoor temperature sensor. Also, adjust the cycle rates and aggressive recovery features in the advanced installer setup.
K
kim78Aug 31, 2025
Why is my American Standard Control Unit heat pump not working?
- R
  rhondafitzgeraldSep 1, 2025
  Your American Standard Control Unit heat pump may not be turning on because the outdoor temperature is below the compressor lockout temperature setting; adjust the compressor lockout temperature setting if desired. Another possibility is that compressor heating lockout is enabled, and the outdoor temperature sensor is out of calibration or has failed; check/repair the outdoor sensor or wiring. Finally, the outdoor unit may not be reporting (Err.126.00); check the communication status of the outdoor unit.
E
erin32Sep 2, 2025
What to do if my American Standard Control Unit screen is not responding?
- M
  Michael OconnellSep 2, 2025
  If your American Standard Control Unit screen isn't responding properly, it might be out of calibration. Remove the 1050 Control from the sub base and reset it, then follow the calibration instructions when it reboots. Alternatively, there could be an internal 1050 Control fault; remove the 1050 Control from the sub base and reset it. Finally, Screen Lock may have been enabled; press and hold the Menu button for 5 seconds to override screen lock.
C
Chad LeeSep 4, 2025
Why won't my American Standard Control Unit display turn on?
- A
  amanda21Sep 4, 2025
  If your American Standard Control Unit display won't turn on, it may be due to a loss of 24VAC between R & B at the 1050 Control. Check the wiring between R & B. Also, check the transformer for 24VAC output. Finally, check for a broken or shorted thermostat wire.
A
Amber AdamsSep 6, 2025
How to correct an incorrect temperature display on my American Standard Control Unit?
- R
  Roy MitchellSep 6, 2025
  To correct an incorrect temperature display on your American Standard Control Unit, calibrate the temperature sensor from the 1050 Control’s menu. It's also possible that surrounding air flow is affecting the sensed temperature of the 1050 Control.

American Standard AccuLink Platinum 1050 Specifications

General

Type	Smart Thermostat
Wi-Fi Enabled	Yes
Touchscreen	Yes
Connectivity	Wi-Fi
Display	Color Touchscreen
Alerts	Yes, System Alerts and Maintenance Reminders
Warranty	5-year limited warranty
Energy Saving Features	Smart Scheduling
Mobile App	Yes
Voice Control	Amazon Alexa, Google Assistant
Features	Remote Access
Programmable	Yes, 7-day programming
Energy Monitoring	Yes
Compatibility	Works with most HVAC systems including gas, oil, electric, and heat pump systems