American Standard S9V2B080D4VSAB - Integrated Furnace Control Menu; Control System Menu

18-CE03D1-1F-EN
97
Integrated Furnace Control Menu
STATUS MENU
ACTIVE ERRORS
Example
1
st
stage Gas Heat
Example
800 CFM
Example
2
nd
Stage Pressure
Switch Error
Example
1st Stage Pressure
Switch Error
LAST 6 FAULTS
Example
2
nd
Stage Pressure
Switch Error
Example
1st Stage Pressure
Switch Error
Example
Open Limit Switch
Error
Control Release#
Example
So!ware Version #
Cooing Off Delay
Example
seconds
Example
Enhanced Mode
OD Tonnage
Example
OD Nominal Tonnage
OD Unit Type
Example
Single Stage
Con$nuous Fan
Example
50% Cooling Airflow
Cooliing CFM
per Ton
Example
CFM per Ton
Heat Off Delay
Example
Seconds
Inter-Stage Delay
Example
Seconds
Gas Hea$ng CFM
Example
2
nd
stage Hea$ng CFM
S9V2-VS
Control System Menu
Example
2 stage 1 compressor
Example
2 stage 2 compressor
CLEARING THE LAST6 FAULTS: To clear the stored faults, scroll to the last 6 faults menu, enter the menu by scrolling to the right and hold the “Op$on” key for at least 5 seconds. Release and a set of 3 dashes will be seen 3 $mes. This confirms the faults have been cleared
SETTING UP YOUR SYSTEM: To change any factory default value, first remove any “call” from the furnace and allow any fan off delays to finish. ( should be seen on the display) Scroll to the selected Menu item by momentarily depressing the “MENU” key and then depress the “OPTION” key to the desired se*ng. Then momentarily depress the “MENU” key again to save the change.
CFM per Ton selec$ons range from 290 – 450 Important: When applied with zoning or a VSPD outdoor unit, the CFM/Ton must be set to 400
Gas Hea$ng CFM shown is 2
nd
stage airflow. 1
st
stage
airflow is ~80% of the selected 2
nd
stage airflow and
cannot be adjusted. Gas hea$ng CFM can be adjusted while the unit is opera$ng in gas heat mode to enable the technician to quickly adjust to the manufacturer's suggested heat rise across the heat exchanger. Mulply the value shown by 10 for actual airflow Model Gas Heang CFM [ ]=Default Upflow S9V2B040U3VS 088 [088], 140, 065, 083 S9V2B060U3VS 103 [103], 113, 130, 080 S9V2B080U4VS 133 [133], 146, 120, 126 S9V2C100U4VS 183 [183], 145, 162, 172 S9V2D120U5VS 195 [195], 225, 156, 185 Downflow S9V2B080D4VS 133 [133], 146, 120, 126 S9V2C100D4VS 183 [183], 189, 150, 162
Model ODT Opons [ ]= Default Upflow S9V2B040U3VS 3T[3T], 1.5T, 2T, 2.5T S9V2B060U3VS 3T[3T], 1.5T, 2T, 2.5T S9V2B080U4VS 4T[4T], 2.5T, 3T, 3.5T S9V2C100U4VS 4T[4T], 2.5T, 3T, 3.5T S9V2D120U5VS 5T[5T], 3.5T, 4T, 4.5T Downflow S9V2B0
80
D4V
S
4T[
4T],
2.5
T,
3T, 3.5T
S9V2C100D4VS 4T[4T], 2.5T, 3T, 3.5T
Hea$ng CFM
per Ton
Example
CFM per Ton
Run Test Mode
See Run Test Menu