Ametek Sorensen XG 600-2.6 User Manual

PROGRAMMABLE POWER
M370430-01 Rev F www.programmablepower.com
XG Family Programmable DC
Power Supply
Operating Manual
(firmware v 2.0 and higher)
670 Watts – 1700 Watts
Half Rack
Full Rack
6 V to 600 V Models:
6-110
6-220
6-220
8-100
8-187.5
8-200
12-70
12.5-120
12-140
20-42
20-76
20-84
33-25
30-50
33-50
40-21
40-38
40-42
60-14
60-25
60-28
80-10.5
80-19
80-21
100-8.5
100-15
100-17
150-5.6
150-10
150-11.2
300-2.8
300-5
300-5.6
600-1.4
600-2.6
600-2.8

Ametek Sorensen XG 600-2.6 Specifications

General

Model	XG 600-2.6
Output Voltage	0-600 V
Output Current	0-2.6 A
Power Rating	1560 W
Output Type	DC
Number of Outputs	1
Cooling	Forced air
Frequency	47-63 Hz
Load Regulation	<0.01%
Line Regulation	<0.01%
Operating Temperature	0 to 50°C
Storage Temperature	-40 to 70°C
Humidity	0 to 95% RH, non-condensing
Protections	Overvoltage, Overcurrent, Overtemperature
Interface	GPIB, RS232
Efficiency	>86%

Summary

Warranty Terms

Product Return Procedure

Outlines the steps for requesting a Return Material Authorization (RMA) number.

Important Safety Instructions

WARNING: High energy and high voltage

Caution regarding high energy and potentially lethal voltages in the power supply.

WARNING: Fire hazard

Caution to operate in a non-flammable environment and avoid unauthorized modifications.

CAUTION: For use as a battery charger

Advises on using appropriate fuses/breakers for battery charging applications.

Installation

Basic Setup Procedure

Provides a summary of the basic setup procedure for the power supply installation.

Step 1: Inspecting and Cleaning

Details the physical check procedure upon receiving the power supply unit.

Step 2: Location and Mounting

Describes rack mounting and ventilation requirements for power supply installation.

Step 3: Connecting AC Input Power

Instructions for safely connecting the AC input power to the power supply.

Step 4: Selecting Load Wires

Details current carrying capacity recommendations for load wiring selection.

Step 5: Performing Functional Tests

Procedure for powering the power supply on/off and checking voltage/current modes.

Step 6: Connecting Loads

Describes DC output connectors for different XG models (6-40V, 60-150V, 300-600V).

Step 7: Connecting Remote Sensing

Instructions for connecting remote sensing wires to adjust regulation point.

Local Operation

Configuring Settings from the Front Panel

Explains front panel controls like mode selection and adjustment.

Navigating the Menu System

Describes the procedure for navigating the XG's menu system.

Alarms and Errors

Details various alarms, errors, and procedures for clearing them.

Using Over Voltage Protection (OVP)

Explains the OVP circuit and how to configure the OVP set point.

Using Under Voltage Protection (UVP)

Details the UVP function and how to define the UVP set point.

Using Multiple Power Supplies

Provides guidance on operating multiple power supplies in series or parallel.

Analog Programming (APG) and Isolated Analog Programming (ISOL)

Analog Programming (APG) of Output Voltage and Output Current

Describes controlling output voltage and current via analog input sources.

Voltage-Controlled Voltage APG Setup

Steps to activate APG voltage mode using an external voltage source.

Isolated Analog Programming Mode (ISOL)

Details the ISOL mode, including AUX Output and ISOL Connector.

Voltage-Controlled Voltage ISOL Setup

Steps to activate ISOL programming voltage mode with an external voltage source.

Remote Operation

Hardware and Connection Setup

Information on setting up connections for RS-232, RS-485, and USB interfaces.

Selecting the Appropriate Communication Port

Status Reporting in SCPI

Reset Command

Locking and Unlocking the Front Panel

Auto Sequence Programming

Communications Options

SETTING UP LAN/ETHERNET

LOCAL AREA NETWORK (LAN) OPTION

Communication Configuration

AMETEK LXI DISCOVERY BROWSER

AMETEK ENETTEST UTILITY

SETTING LAN PARAMETERS

Setting a Static IP Address through Ethernet, USB, Serial Interfaces

SYSTEM COMMANDS

LXI COMPLIANCE

Calibration and Troubleshooting

Main Voltage and Current Calibration Principle

Calibrating the Output Voltage

Calibrating the Output Current

Over Voltage Protection Calibration

Non-isolated Analog Programming Calibration

Restore Factory Calibration

Emergency Shutdown

Troubleshooting for Operators

APPENDIX A SCPI Command Reference

Using SCPI Commands

SCPI Command Summary

APPENDIX B Error Messages

Error Messages

Command Error List

Execution Error List

Device-Specific Error List

APPENDIX C Specifications

Electrical Specifications for XG Family, 850 W

Electrical Specifications for XG Family, 1500 W

Electrical Specifications for XG Family, 1700 W

Common Specifications for All Models

APPENDIX D Rack Mount Options and Installation Instructions

Rack Mount Kit Options

Location Requirements

Mounting Option A: 1U Rails

Mounting Option B: Manufactured Slides from Jonathan® Engineered Solutions

APPENDIX E Lantronix Procedures for MEA Option

Setting Up the Computer

Software Installations

Configuring the Device Using DeviceInstaller

Assigning an IP Address to the Power Supply Unit

Selecting ENET as the Communication Port

Troubleshooting for XG 850W Model with ENET and/or RS-485 Communication