Ametek Sorensen XG 600-2.6 - Page 17

Contents
M370430-01 Rev F xv
Figure 4-4 Programming Output Voltage using an External Voltage Source ................... 4-9
Figure 4-5 Programming Output Current using an External Voltage Source ................... 4-9
Figure 4-6 Programming Output Voltage using an External Resistor ............................ 4-14
Figure 4-7 Programming Output Current using an External Resistor ............................ 4-14
Figure 4-8 Voltage Readback Using APG Connector J1 ............................................... 4-19
Figure 4-9 Current Readback Using APG Connector J1 ................................................ 4-19
Figure 4-10 AUX Output and ISOL Connector Pinout ...................................................... 4-20
Figure 4-11 Programming Output Voltage using an Isolated External Voltage Source ... 4-22
Figure 4-12 Programming Output Current using an Isolated External Voltage Source ... 4-22
Figure 4-13 Programming Output Voltage using an Isolated External Resistor .............. 4-27
Figure 4-14 Programming Output Current using an Isolated External Resistor ............... 4-27
Figure 4-15 Isolated Voltage Monitoring........................................................................... 4-32
Figure 4-16 Isolated Current Monitoring ........................................................................... 4-32
Figure 5-1 Remote Control Connectors............................................................................ 5-3
Figure 5-2 RS-232 Communication Cable with DB-9 Pinout............................................ 5-5
Figure 5-3 DB-25 Pinout ................................................................................................... 5-5
Figure 5-4 RS-232 Communication Cable with DB-25 Pinout.......................................... 5-6
Figure 5-5 RS-485 Communication Cable with DB-9 ....................................................... 5-7
Figure 5-6 RS-485 Communication Cable from Master to Slave Unit .............................. 5-8
Figure 5-7 Found New Hardware Wizard ....................................................................... 5-10
Figure 5-8 Install Hardware Device Drivers .................................................................... 5-10
Figure 5-9 Completing the New Hardware Wizard ......................................................... 5-11
Figure 5-10 Device Manager ............................................................................................ 5-12
Figure 5-11 Communications Port (COM1) Properties .................................................... 5-13
Figure 5-12 Completing the new hardware wizard ........................................................... 5-13
Figure 5-13 Scanning for Instruments .............................................................................. 5-17
Figure 5-14 Instrument Properties ................................................................................... 5-18
Figure 5-15 Multi Power Supply Connection to RS-485 Bus............................................ 5-19
Figure 5-16 USB Settings ................................................................................................. 5-22
Figure 5-17 ASCII Setup .................................................................................................. 5-23
Figure 5-18 SCPI Status Reporting Model ....................................................................... 5-30
Figure 5-19 IEEE 488.2 Register Model ........................................................................... 5-31
Figure 5-20 Summary of Standard Event Status Register ............................................... 5-36
Figure 5-21 SCPI Register Model ..................................................................................... 5-38
Figure 5-22 Operation Status Register Fanout ................................................................ 5-39
Figure 5-23 SCPI QUEStionable Registers Fanout ......................................................... 5-48
Figure 6-1 Computer or HUB Plug ................................................................................... 6-3
Figure 6-2 Power Supply Plug .......................................................................................... 6-3
Figure 6-3 RJ-45 Plug....................................................................................................... 6-3
Figure 6-4 Scheme of ENET Cross-Cable ....................................................................... 6-4
Figure 6-5 XPort® ENET Connector and LEDs ............................................................... 6-4
Figure 6-6 Single Computer, Single Power Supply .......................................................... 6-6
Figure 6-7 PC on Same Side of Router as Power Supply................................................ 6-8
Figure 6-8 Home Page ..................................................................................................... 6-9
Figure 6-9 AMETEK LXI Discovery Browser .................................................................... 6-9
Figure 6-10 Power Supply Hidden Behind a Router ........................................................ 6-10
Figure 6-11 Router Home Page ....................................................................................... 6-11
Figure 6-12 Port Forwarding ............................................................................................. 6-12
Figure 7-1 Offset (Intercept) Error and Gain (Slope) Error ............................................... 7-3
Figure 7-2 Calibration: Step 1 Gain Calibration ................................................................ 7-4
Figure 7-3 Calibration: Step 2 Offset Calibration .............................................................. 7-4
Figure 7-4 Calibration: Step 3 Recalibrate Gain ............................................................... 7-5