Ametek Sorensen XG 80-21 User Manual

PROGRAMMABLE POWER
M370430-01 Rev F www.programmablepower.com
XG Family Programmable DC
Power Supply
Operating Manual
(firmware v 2.0 and higher)
670 Watts – 1700 Watts
Half Rack
Full Rack
6 V to 600 V Models:
6-110
6-220
6-220
8-100
8-187.5
8-200
12-70
12.5-120
12-140
20-42
20-76
20-84
33-25
30-50
33-50
40-21
40-38
40-42
60-14
60-25
60-28
80-10.5
80-19
80-21
100-8.5
100-15
100-17
150-5.6
150-10
150-11.2
300-2.8
300-5
300-5.6
600-1.4
600-2.6
600-2.8

Ametek Sorensen XG 80-21 Specifications

General

Output Voltage	0-80V
Output Current	0-21A
Power Rating	1680W
Output Type	DC
Input Frequency	47-63Hz
Programming Interface	RS-232
Efficiency	85% typical
Operating Temperature	0°C to 50°C
Cooling	Forced air cooling
Protections	Over Voltage, Over Current, Over Temperature

Summary

Important Safety Instructions

High Energy and High Voltage Warning

Caution regarding stored energy and potentially lethal voltages at output terminals.

Fire Hazard Warning

Warning to operate in a non-flammable environment and avoid unauthorized modifications.

Limitations on Use Warning

Specifies that the DC Power Supply is not for life support or medical devices.

Installation Procedures

Basic Setup Procedure

Summarizes the essential steps for installing the power supply.

Step 1: Inspecting and Cleaning

Step 2: Location and Mounting

Step 3: Connecting AC Input Power

Details how to connect the AC input power to the power supply.

Step 4: Selecting Load Wires

Step 5: Performing Functional Tests

Outlines procedures for performing functional checks on the power supply.

Step 6: Connecting Loads

Describes how to connect loads to the power supply for single and multiple loads.

Local Operation of the XG Power Supply

Configuring Settings from the Front Panel

Details how to configure settings using the front panel controls.

Operating Modes

Alarms and Errors

Information on identifying, understanding, and clearing alarms and errors.

Protection Features

Details on Over Voltage, Under Voltage, Over Current, and Over Temperature protections.

Resetting the Power Supply

Analog and Isolated Analog Programming

Analog Programming (APG) of Output Voltage and Current

Isolated Analog Programming Mode (ISOL)

Remote Operation

Hardware and Connection Setup

Selecting the Appropriate Communication Port

Status Reporting in SCPI

Reset Command

Auto Sequence Programming

Configure Other Protection Mechanisms

Communications Options

SETTING UP LAN/ETHERNET

LOCAL AREA NETWORK (LAN) OPTION

Communication Configuration

SETTING LAN PARAMETERS

SETTING A STATIC IP ADDRESS

SYSTEM COMMANDS

Calibration and Troubleshooting

Understanding the Calibration Principle

Calibrating the Output Voltage

Procedure for performing gain and offset calibration for output voltage.

Calibrating the Output Current

Procedure for performing gain and offset calibration for output current.

Over Voltage Protection Calibration

Steps to calibrate the over voltage protection feature of the power supply.

Non-isolated Analog Programming Calibration

Calibration Procedure for Isolated Modes

Restore Factory Calibration

Restore Default Calibration

User Diagnostics

Emergency Shutdown

Steps to perform in an emergency situation to shut down the unit.

Unusual or Erratic Operation

Troubleshooting steps for addressing unusual or erratic power supply behavior.

SCPI Command Reference

SCPI Command Summary

A summary table of supported SCPI commands.

SCPI Commands for Output Control

Commands for controlling output voltage, current, and power.

SCPI Commands for Calibration

SCPI commands used for various calibration procedures.

System Commands

Error Messages

Command Error List

Execution Error List

Device-Specific Error List

Query Error List

Specifications

Electrical Specifications for XG Family, 850 W

Detailed electrical specifications for the XG 850 Watt models.

Electrical Specifications for XG Family, 1500 W

Detailed electrical specifications for the XG 1500 Watt models.

Electrical Specifications for XG Family, 1700 W

Detailed electrical specifications for the XG 1700 Watt models.