Ammann ARX 26-2

To Next Page

To Previous Page

18 ARX 23-2 T4i, ARX 26-2 T4i

Main Page

Table of Contents8
Contents8
Specification Manual13
Basic Data14
Dimensional Drawing of the Machine16
Technical Data18
Operating Manual23
Main Safety Precautions25
Safety Precautions During Operation of the Machine25
Before Compacting Works Are Started25
Work in the Dangerous Area25
Ensurance of Safety Measures by the Provider26
Protective ROPS Frame26
Requirements for the Qualification of Machine Operators27
Driver's Obligations28
Forbidden Activities - Safety and Guarantee29
Safety Notices and Signs Applied on the Machine31
Hand Signals35
Environmental and Hygiene Principles38
Hygiene Principles38
Environmental Principles38
Preservation and Storage39
Short-Term Preservation and Storage for 1-2 Months39
Preservation and Storage of the Machine for a Period over 2 Months39
Machine Depreservation41
Machine Disposal after Its Service Life43
Machine Description44
Controls and Checking Instruments46
Dashboard and Control Panels47
Machine Operation and Use64
Starting the Engine65
Drive and Reverse Drive69
Stopping the Machine and Turning off the Engine77
Machine Emergency Stop77
Machine Parking79
Panic Response79
Sprinkling81
ACE Force (Optional Equipment)81
Infrathermometer (Optional Equipment)82
ROPS Lifting and Lowering88
Lowering and Raising of the ROPS Frame with a Plastic Canopy90
Telematics Readiness96
Edge Cutter (Optional Equipment)97
Calibration Mode98
Lowering and Raising of the Plastic Canopy101
Machine Transport103
Loading the Machine104
Loading the Machine Using a Ramp104
Loading the Machine Using a Crane105
Special Conditions to Use the Machine106
Towing the Machine106
Drum Offset108
Machine Operation During Initial Run Period109
Machine Operation at Low Temperatures109
Machine Operation at Higher Temperatures and Humidity109
Machine Operation at Higher Altitudes109
Machine Operation in Dusty Environment110
Driving with Vibration on Compacted and Hard Materials110
Maintenance Manual111
Safety and Other Measures During Maintenance of the Machine113
Safety During Machine Maintenance113
Fire Protection When Operating Fluids Are Changed113
Environmental and Hygiene Principles114
Specification of Operating Fluids115
Engine Oil115
Fuel116
Coolant117
Hydraulic Oil118
Lubricating Grease118
Emulsion118
Fluids119
Lubrication and Maintenance Chart120
Lubrication and Service Plan122
Lubrication and Maintenance Operations123
Every 20 Hours of Operation (Daily)124
Fuel Check124
Engine Oil Check125
Engine Coolant Check126
Checking the Oil in the Hydraulic Tank127
Cleaning the Hydraulic Oil Cooler128
Air Filter Check129
Sprinkling Emulsion Level Check130
Sprinkling Tank Refilling131
Scraper Adjustment131
Inspection of Warning and Checking Devices132
Engine Leakage Check134
Check of the Fan and Engine Belt for Condition134
Brake Test135
Check of the Parking Brake135
Check of the Emergency Brake136
Check of the Service Brake137
Check of the Tightness of the Fuel and Hydraulic System138
Every 50 Hours of Operation139
Check of Hoses and Clips139
Battery Inspection140
Every 100 Hours of Operation141
Air Filter Cleaning141
Cleaning the Water Separator on the Fuel Filter142
Machine Lubrication143
Tyre Pressure Check144
Every 250 Hours of Operation145
Fuel Filter Replacement145
Engine Oil Change146
Checking the Hoses of the Engine Cooler for Wear and Mounting148
Checking the Hoses and Clips for Mounting148
Sprinkling Filter Cleaning149
Engine Intake Pipe Inspection150
Every 500 Hours of Operation, but at Least Once a Year151
Fuel Tank Cleaning151
Electrical Installation Inspection152
Replacement of the Fuel Separator Filter Cartridge152
Valve Clearance Check and Adjustment153
Engine Cooler Cleaning153
Check of Rubber-Metal Elements of the Engine Cooler154
Every 1000 Hours of Operation155
Hydraulic Oil Change and Filter Replacement155
Replacement of Air Filter Cartridges157
Damping System Check159
Swinging Support Check160
Articulation Joint Check160
Every 2000 Hours of Operation161
Engine Belt Replacement161
Engine Coolant Change161
Replacement of Hoses of the Cooling System163
Replacement of Rubber-Metal Elements of the Engine Cooler163
Replacement of Hoses of the Fuel System164
Replacement of Suction Hoses164
Maintenance as Required165
Gas Strut Replacement165
Cleaning the Water Separator166
Cleaning the Water Tank166
Cleaning the Machine167
Draining Water from the Sprinkling Circuit before the Winter Season168
Fuel System Venting168
Charging of the Battery170
Checking the Screw Connections for Tightening171
Troubleshooting173
List of Error Codes Displayed on the Display174
Appendices182
Wiring Diagram182
Hydraulic Diagram ARX 23-2 T4I, ARX 26-2 T4I188
Hydraulic Diagram ARX 23-2C, ARX 26-2C190
Table of Spare Parts for Regular Maintenance192
Content of the Filter Set after 250 Hours (4-760243)193
Content of the Filter Set after 500 Hours (4-760244)193
Content of the Filter Set after 1000 Hours (4-760245)193

Ammann ARX 26-2 - Page 22

Table of Contents

Related product manuals