AMX COLOR TOUCH PANELS WITH AUDIO (G3 FIRMWARE) User Manual

Programming
42
4" Color Touch Panels with Audio
Serial Commands (Cont.)
CHECK CAL
Enters the calibra-
tion test mode.
Syntax:
"CHECK CAL"
Example:
CHECK CAL
Begins the calibration check mode on the touch panel.
ECHO ON
Turns On charac-
ter echo.
Syntax:
"ECHO ON"
Example:
ECHO ON
The character echo is sent back to the computer.
ECHO OFF
Turns Off charac-
ter echo.
Syntax:
"ECHO OFF"
Example:
ECHO OFF
The character echo is not sent back to the computer.
GET CAL
Gets the calibra-
tion variables.
Syntax:
"GET CAL"
Example:
GET CAL
Gets the calibration variables on the touch panel.
HELLO
Verifies that serial
communication is
working properly.
Syntax:
"HELLO"
Example:
HELLO
If the communication is active and working, the response is "How are you doing?".
RESET
Cycles power on
the touch panel.
Syntax:
"RESET"
Example:
RESET
Cycles the power on the touch panel. Once the firmware is downloaded, send this com-
mand to recycle power to the panel. This command prevents the user from having to phys-
ically re-cycling power on the unit.
SET CAL
Sets the calibra-
tion variables.
Syntax:
“SET CAL <X Multiplier> <X Offset> <Y Multiplier> <Y
Offset>"
Example:
SET CAL 2F 3A 2B 62
Sets the calibration values on the touch panel.
SETUP
Puts the touch
panel on the
Setup Page.
Syntax:
"SETUP"
Example:
SETUP
Flips the touch panel to the Setup page.

AMX COLOR TOUCH PANELS WITH AUDIO (G3 FIRMWARE) Specifications

General

Brand	AMX
Model	COLOR TOUCH PANELS WITH AUDIO (G3 FIRMWARE)
Category	Touch Panel
Language	English

Summary

AMX Limited Warranty and Disclaimer

Product Information Overview

Product Specifications

Provides detailed technical specifications for the touch panels, including dimensions and memory.

Panel Display and IR Specifications

Details LCD parameters, viewing angles, and IR reception angles for the panels.

Front Panel Component Details

Covers external buttons, LEDs, sensors, IR receiver, and microphone on the front panel.

Panel Interfaces and Environment

Details speaker, audio levels, rear connectors, and operating environment specifications.

Optional Accessories and Cleaning

Lists optional accessories and provides instructions for cleaning the touch overlay.

Water-Resistant Faceplate Installation

Installation Procedures

Mounting AXD Wall Mount Panels

Describes how to mount AXD panels into drywall, conduit boxes, or flat surfaces.

Drywall Installation Techniques

Details installing panels into drywall using expansion clips.

Flat Surface Installation Techniques

Explains mounting panels onto flat surfaces using solid-surface screws.

Removing AXT Faceplate/Bezel

Provides steps for removing the faceplate and bezel from the AXT panel.

Touch Panel Wiring Guide

Covers wiring guidelines and the AXlink/audio connectors.

CP4/A Terminal Connector Wiring

Explains wiring the terminal connector and cables for CP4/A panels.

Using CP4/A Programming Jacks

Details how to connect and use programming jacks for panel setup.

Designing Touch Panel Pages

Button Types and Categories

Describes general button types like selection, information, adjustment, and keypad buttons.

Activating Edit Mode and Main Page Navigation

Explains how to activate edit mode and navigate the main page for design.

Device Configuration Settings

Covers setting the device base and device used for panel configuration.

Page and Button Creation Workflow

Details adding pages, setting page colors, and adding/resizing buttons.

On-Screen Button Properties and Attributes

Explains setting button properties like channel codes, variable text, and borders.

Adding Button Text, Icons, and Bitmaps

Describes how to add text, icons, and bitmaps to buttons for visual customization.

Creating Bargraphs and Joysticks

Setting Button Level Codes

Details setting level codes for joysticks and bargraphs.

Adjust Sensors Setup Page and Configuration

TPDesign3 Download Procedures

Programming Commands Reference

Serial Commands

Lists and explains serial commands for panel control and status reporting.

System Send_Commands

Details commands sent from the controller to the touch panel for operations.

Programming Numbers for Customization

Provides numerical codes for colors, fonts, and border styles for customization.

Shorthand Send Commands

Lists shorthand commands for efficient control and automation of panel functions.

Color Send_Commands Reference

Variable Text Send_Commands Reference

Upgrading the Firmware

Firmware Update Communication Methods

Explains various methods for communicating with the panel for firmware updates.

Upgrading Firmware via COM Port

Details the process of upgrading firmware using a COM port connection from a PC.

Upgrading Firmware via IP Address

Details upgrading firmware using an IP address over a network connection.

Replacing the Battery

AXT-CP4/A Battery Replacement

Step-by-step guide to replace the battery in the AXT-CP4/A panel.

AXD-CP4/A Battery Replacement

Step-by-step guide to replace the battery in the AXD-CP4/A panel.