Why is my Anden A320V1 Dehumidifier producing hot air?
It's normal for the Anden Dehumidifier to produce hot air. The air is reheated as it passes across the condenser coil, which causes the temperature to rise between the inlet and outlet.
How to fix Anden A320V1 Dehumidifier blower running but with little or no airflow?
If your Anden Dehumidifier blower is running with little to no airflow, you should: * Check the dehumidifier's air filter and replace it if needed. * Inspect the ductwork for any blockages and clear them. * Make sure that the outlet collar with backflow damper is installed on the outlet side of the dehumidifier. * Check the backflow damper for any obstructions or if it's stuck, and remove any blockage.
What to do if my Anden A320V1 does not turn on?
If your Anden Dehumidifier is not turning on, make sure that: * The dehumidifier is properly plugged in. * The power switch is in the ON position. * The control is turned ON. * The circuit breaker hasn't tripped.
Why is my Anden A320V1 Dehumidifier not draining properly?
If your Anden Dehumidifier is not draining properly, first ensure that the unit is level. Then, check the drain line for any blockages and make sure it has a continuous downward slope.
How to stop coil frosting in my Anden A320V1 Dehumidifier?
If your Anden Dehumidifier's coil is frosting, it may be due to: * Lack of or reduced airflow: Check the air filter and wash or replace it. * Blocked ductwork: Inspect the ductwork for blockages. * Inlet air conditions below 60°F: Increase the humidity setting.
What causes the Anden A320V1 blower to run but the compressor not?
If the Anden Dehumidifier blower is running, but the compressor isn't, check the connections at the control board and empty the condensate pan if a float switch is installed. If there is no float switch installed, ensure the jumper is installed at the float switch terminals on the control board.
What does error E7 mean on my Anden Dehumidifier and how do I fix it?
If the Anden Dehumidifier displays error code E7, you should empty the condensate pan and check the float switch connection at the control board. If you are not using a float switch, verify that the jumper is between the float switch terminals on the dehumidifier control board. If the problem continues, consider replacing the float switch.
How to troubleshoot error code E4 on Anden Dehumidifier?
If the Anden Dehumidifier displays error code E4, check the frost sensor connection at the power board and ensure the terminal is fully seated. Remove the side access panel and verify that the sensor is secured to the suction line. Reset the fault by cycling power to the dehumidifier. Turn the humidity setting down (below room/home humidity level) to make a dehumidification call. Allow the fan and compressor to run for approximately 10-15 minutes and then enter diagnostic test mode. Record values and call Technical Support.
What does error code E5 mean on my Anden Dehumidifier?
If the Anden Dehumidifier displays error code E5, check the high temperature sensor connection at the power board, ensuring the terminal is fully seated. Remove the side access panel and verify the sensor is not damaged and is connected to the refrigeration line coming from the compressor. It may need to be replaced with Part No. 5456 – contact Technical Support to confirm.
How do I fix error code E6 on my Anden Dehumidifier?
If the Anden Dehumidifier displays error code E6, check the low temperature sensor connection at the power board. Remove the side access panel and verify the sensor is not damaged and connected to the suction line. It may need to be replaced with Part No. 5455 – contact Technical Support to confirm.
Steps and logic for operating the dehumidifier using its on-board control interface.
Instructions for operating the dehumidifier when controlled by the Model A77 external unit.
Lists and explains error codes displayed by the dehumidifier for fault identification.
General| Brand | Anden |
|---|---|
| Model | A320V1 |
| Category | Dehumidifier |
| Language | English |
To Next Page
