What to do if Anden A100 does not turn on?
If your Anden dehumidifier isn't turning on, first ensure it's properly plugged in and the power switch is in the ON position. Also, check that the control is turned ON and verify that the circuit breaker hasn't tripped.
Why is my Anden Dehumidifier not draining properly?
If your Anden dehumidifier isn't draining correctly, make sure the unit is level. Inspect the drain line for any blockages and ensure it has a continuous downward slope. Also, check for the presence and condition of the drain insert.
How to fix Anden Dehumidifier with low airflow?
If the blower in your Anden dehumidifier is running but there's little to no airflow, the pressure drop across the dehumidifier might be too high. Start by checking the dehumidifier's air filter and replace it if it's dirty. Also, inspect the ductwork for any blockages and clear them.
What to do if Anden A100 blower runs but compressor doesn't?
If your Anden dehumidifier's blower is running, but the compressor isn't, it could be due to an open float switch. If a float switch is installed, check its connections at the control board and empty the condensate pan. If there's no float switch, verify that the jumper is installed at the float switch terminals on the control board.
What does E7 error mean on Anden A100 Dehumidifier?
The E7 error code on your Anden dehumidifier indicates that the float switch is open. You should empty the condensate pan and check the float switch connection at the control board. If you're not using a float switch, make sure there's a jumper between the float switch terminals on the dehumidifier control board. If the problem continues, the float switch may need to be replaced.
What does E3 error mean on Anden Dehumidifier?
The E3 error code on your Anden dehumidifier indicates a Model A77 Remote Control Communication Loss. Check the connections between the Model A77 and the dehumidifier control board, ensuring the terminals are fully inserted and secured. If connections are correct, turn off the dehumidifier, remove the Model A77, and reconnect it using a short 4-wire cable. Turn the dehumidifier back on and increase the dryness level on the Model A77. If it turns on, the issue is with the wiring. If not, contact Technical Support.
What does E4 error mean on Anden A100?
The E4 error code on your Anden dehumidifier indicates insufficient capacity. Check the frost sensor connection at the power board, ensuring the terminal is fully seated. Remove the side access panel and verify the sensor is secured to the suction line. If it's connected, reset the fault by cycling power. Lower the humidity setting to make a dehumidification call. Let it run for 10-15 minutes, then enter diagnostic test mode by pressing the UP ARROW and MODE buttons for 3 seconds. Record the displayed temperature, humidity, and frost sensor temperature values, and contact Technical Support.
What does E5 error mean on Anden A100 Dehumidifier?
The E5 error code on your Anden dehumidifier indicates a High Temperature Thermistor Failure. Verify the high temperature sensor connection at the power board is secure. Remove the side access panel and ensure the sensor is undamaged and connected to the refrigeration line coming from the compressor. If the sensor is properly connected, it may need to be replaced; contact Technical Support for confirmation.
What does E6 error mean on Anden A100 Dehumidifier?
The E6 error code on your Anden dehumidifier indicates a Low Temperature Thermistor Failure. Check the low temperature sensor connection at the power board. Remove the side access panel and verify the sensor is not damaged and connected to the suction line. If the sensor is connected and secured to the refrigeration line, it may need to be replaced; contact Technical Support to confirm.
What does E8 error mean on Anden A100?
The E8 error code on your Anden dehumidifier indicates that the inlet air temperature is out of the 50°F – 104°F range or the dew point is below 40°F. Verify that all ductwork is properly sealed. If there are no signs of leak points, contact Technical Support.
Critical safety warnings about severe hazards like electric shock and physical injury.
Precautions and warnings for safe installation, use, and maintenance of the dehumidifier.
Lists all items included in the dehumidifier package for user verification.
Instructions on attaching inlet and outlet duct collars for different installation types.
Step-by-step guide on how to relocate the dehumidifier's control panel.
Guidance on optimal placement, clearances, and service access for the unit.
Warning against damaging the critical drain insert component.
Alert about potential condensate leaks if the unit operates without the drain insert.
Step-by-step guide for installing and connecting the Model A77 remote control.
Guidance on using other external humidity control systems with the dehumidifier.
Configuration options for using the Model A77 or other remote controls.
Configuration options for using external controls like thermostats.
Specific mode within the installer test to verify dehumidification function.
Instructions for operating the dehumidifier using its on-board control.
Instructions for operating the dehumidifier with the Model A77 remote control.
Procedure for checking and cleaning or replacing the air filter.
Highlights the criticality of the drain insert for proper dehumidifier operation.
Alert regarding condensate leaks if the unit runs without the drain insert.
Step-by-step instructions for safely removing the drain insert.
Step-by-step instructions for correctly reinstalling the drain insert.
Explanation of diagnostic codes, their failure modes, and recommended actions.
Instructions for registering the product warranty online or by mail.
General| Brand | Anden |
|---|---|
| Model | A100 |
| Type | Dehumidifier |
| Dehumidification Capacity | 100 pints per day |
| Power Supply/Voltage | 115V, 60 Hz |
| Drain Type | Gravity Drain |
| Tank Capacity | N/A (Designed for continuous drainage) |
To Next Page
