Angelcare AC337 - User Manual

Questions and Answers

J
Jay NguyenAug 17, 2025
What to do if Angelcare AC337 emits loud noises?
- B
  Brenda OrtegaAug 18, 2025
  If your Angelcare Baby Monitor is emitting loud noises (feedback), move the units further apart, at least 3 meters. You can also try decreasing the volume on the Parent Unit.
J
John ReyesAug 20, 2025
Why is there no sound on my Angelcare AC337 Baby Monitor?
- J
  Jose HamiltonAug 20, 2025
  If no sound is being transmitted on your Angelcare Baby Monitor, first check the volume level on both the Parent Unit and the Nursery Unit to ensure they are appropriately set. Also, try bringing the Parent Unit closer to the Nursery Unit. Ensure that the Parent Unit is adequately charged.
S
Stephen BrownAug 23, 2025
What to do if my Angelcare Baby Monitor has weak reception?
- J
  Jeremy WilsonAug 23, 2025
  If your Angelcare Baby Monitor has weak reception, try the following: * Bring the units closer together. * Change the position of one or both units. * Place the units on a flat surface, out of the baby's reach. * Recharge the Parent Unit.
W
Wyatt PaulAug 26, 2025
What to do if my Angelcare Baby Monitor has static?
- A
  Amber ColemanAug 26, 2025
  If your Angelcare Baby Monitor is experiencing static, distortion, or interference, rotate the Parent Unit or move it away from the source of interference.
B
bjonesAug 27, 2025
How to fix black screen on Angelcare AC337?
- B
  Bobby WatsonAug 27, 2025
  If the screen on your Angelcare Baby Monitor Parent Unit is black, first, turn the unit back on by pushing and holding the POWER ON/OFF button for 2 seconds. If that doesn't work, recharge the Parent Unit.
K
kimberlychavezAug 30, 2025
Why does my Angelcare movement sensor pad have false alarms?
- E
  Elizabeth BarnesAug 30, 2025
  If your Angelcare movement sensor pad is giving false alarms, consider these potential solutions: * Replace the Sensor Pad battery CR2450. * Turn OFF the Nursery Unit. * Ensure the Nursery Unit is turned OFF after removing the baby from the cot. * Make sure there is no bedding between the mattress and the Sensor Pad. * Ensure the Sensor Pad is on a flat, firm surface with the printed side facing up. * Adjust the sensitivity level. Refer to Warnings 3 to 11 and see STEP 4, TEST THE SENSOR PAD.
D
dennis36Sep 1, 2025
What to do if Angelcare AC337 has weak reception?
- S
  swheelerSep 2, 2025
  If you're experiencing weak reception with your Angelcare Baby Monitor, try these steps: Bring the units closer together, change the position of either the parent unit or the nursery unit, place the units on a flat surface away from the baby's reach, and ensure the parent unit is fully recharged.
T
Tracy WilsonSep 4, 2025
Why is there no sound being transmitted on my Angelcare Baby Monitor?
- E
  Edward SilvaSep 4, 2025
  If no sound is being transmitted on your Angelcare Baby Monitor, first check the volume levels on both the Parent Unit and the Nursery Unit to ensure they are appropriately set. If the volume is adequate, try moving the Parent Unit closer to the Nursery Unit. Also, ensure that the Parent Unit is adequately charged.
D
Diane HoweSep 6, 2025
What to do if Angelcare AC337 Baby Monitor parent unit screen is black?
- N
  Nicole PhillipsSep 7, 2025
  If the Parent Unit screen on your Angelcare Baby Monitor is black, try turning the unit back ON by pushing and holding the POWER ON/OFF button for 2 seconds. If that doesn't work, recharge the Parent Unit.
W
William NelsonSep 9, 2025
What to do if Angelcare Baby Monitor has static, distortion, interferences?
- B
  Brenda HansenSep 9, 2025
  If your Angelcare Baby Monitor is experiencing static, distortion, or interference, rotate the Parent Unit or move it away from the source of interference.