EasyManua.ls Logo

Angelcare AC601 - User Manual

Angelcare AC601
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
OWNER’S MANUAL
SIMPLICITY MOVEMENT SENSOR
WITH SOUND BABY MONITOR
Model AC601
for your peace of mind
Movement Alarm
Your monitor comes with the movement alarm activated.
When switching on your monitor it will alarm, with or without
the Sensor Pad plugged in, if no movement is detected.
Deactivate the movement function to use the monitor without
the Sensor Pad.
Channel Selection
When monitoring sound and/or movement, the channel options
on both Parent and Nursery Unit must be set to the same
position: A, B or C. This can be done by sliding the switches on
the left side of both units to the markings indicating A, B or C.
Cord Safety
Ensure the Nursery Unit is at least 1 metre away from your
baby’s cot. The Sensor Pad cord must always be kept out of
reach of baby and secured using the cord cover kit provided.
Voice-activated Sound Transmission
Your monitor will transmit when it detects sound from
your baby or in their room. You can adjust the microphone
sensitivity to suit your needs.
DON’T
FORGET
IMPORTANT ADVICE FOR INITIAL SETUP
PLEASE FOLLOW THE INSTRUCTIONS CAREFULLY FOR CORRECT SETUP
Please DO NOT return this product to the store. For assistance please
contact our helpline on 0345 009 1789 or email helpline@babyhelpline.co.uk
Mon – Fri 10am – 4pm, excluding bank holidays.

Table of Contents

Questions and Answers

  • M
    Maria CrawfordAug 19, 2025
    Why does my Angelcare AC601 Baby Monitor keep giving false alarms?
    • S
      Steven DaltonAug 19, 2025
      If your Angelcare Baby Monitor is giving false alarms, there are several potential causes and solutions: * The sensitivity level of the Sensor Pad might be too low. In this case, increase the sensitivity level. * Ensure the Sensor Pad is in full contact with the crib and resting on a flat, firm mattress surface, with no bedding in between. * Check that the Sensor Pad cord is properly connected to the Nursery Unit by unplugging and reconnecting it. * It may also help to turn the Nursery Unit off.
  • D
    Daryl ArnoldAug 21, 2025
    Why is the reception so weak on my Angelcare AC601 Baby Monitor?
    • R
      Rachael PowersAug 21, 2025
      If you're getting very weak reception on your Angelcare Baby Monitor, here are some things to try: * Bring the Parent Unit closer to the Nursery Unit. * If either unit is near a large metal mass, change its position. * Ensure both units are placed on a flat surface away from the baby's reach and in an upright position. * Check or replace the batteries.
  • D
    Dennis SmithAug 23, 2025
    Why is the power indicator light not on on my Angelcare AC601?
    • T
      tmooreAug 23, 2025
      If the power indicator light isn't lighting up on your Angelcare Baby Monitor, check the following: * Make sure the batteries are not low and are properly installed. Replace them if necessary. * Ensure the AC adapters are correctly connected and the electrical outlet is working. Try a different outlet if needed. * Confirm that both units are turned on.
  • A
    Amanda BoothAug 26, 2025
    Why is there no sound coming from my Angelcare AC601 Baby Monitor?
    • O
      oblevinsAug 26, 2025
      If you're not getting any sound from your Angelcare Baby Monitor, consider these possibilities: * The Parent and Nursery Units might be too far apart; try bringing them closer. * Check the batteries in both units to ensure they are properly installed and not low. Replace them if necessary. * Verify that the AC adapters are correctly connected and the electrical outlet is working. Try a different outlet if needed. * Make sure both the Parent and Nursery Units are powered on. * Ensure both units are set to the same channel (A, B, or C). * The volume level might be too low; increase it.
  • K
    Kevin OconnorAug 28, 2025
    What to do if the alarm on my Angelcare Baby Monitor will not sound?
    • J
      Jermaine HeathAug 28, 2025
      If the alarm on your Angelcare Baby Monitor isn't sounding, here are a few things to check: * Ensure the Nursery Unit isn't detecting movement from the crib being touched; avoid contact when the monitor is on. * Make sure the Nursery Unit isn't picking up movement from outside the crib, such as motorized devices or strong drafts. If this is the case, place the crib near a solid wall and turn off any devices causing vibrations. You may also need to decrease the sensitivity. * The Sensor Pad sensitivity level might be set too high, so try decreasing it.
  • F
    fleeAug 30, 2025
    How to fix static and interference on my Angelcare AC601 Baby Monitor?
    • C
      Christopher MontgomeryAug 30, 2025
      If you're experiencing static, distortion, or interference with your Angelcare Baby Monitor, try the following: * Ensure the Parent and Nursery Units are not too far apart. * Make sure both units are set to the same channel (A, B, or C). * Verify that both units are turned on. * If the Parent Unit is near motorized devices, fluorescent lights, or a television, try rotating it or moving it away from the source of interference. * Recharge the batteries.
  • M
    marshallalexSep 1, 2025
    How to stop feedback (squealing noises) on my Angelcare AC601 Baby Monitor?
    • J
      Jennifer GarciaSep 1, 2025
      If you're hearing feedback (squealing noises) from your Angelcare Baby Monitor: * Move the units farther apart (at least 10 feet). * Decrease the volume on the Parent Unit.
  • D
    djohnsonSep 4, 2025
    Why is my Angelcare Security Sensor giving false alarms?
    • D
      dmurphySep 4, 2025
      If your Angelcare Security Sensor is giving false alarms, try these solutions: * Turn the Nursery Unit off, then on again. * Increase the sensitivity level (refer to the Movement Sensitivity Adjustment section). * Ensure there is no thick bedding between the mattress and the Sensor Pad. The Sensor Pad must rest on a firm surface. If the crib has a spring or slat base, place a piece of Masonite board measuring at least 13” (33cm) on all four sides and 1/4” (0.64cm) thick. * Unplug and reconnect the cord.
  • S
    Stephanie OrtegaSep 6, 2025
    What to do if my Angelcare Security Sensor has no sound?
    • A
      Austin BrownSep 6, 2025
      If no sound is being transmitted by your Angelcare Security Sensor, please check the following: 1. Bring the Parents Unit closer to the Nursery Unit. 2. Check or replace the batteries in both units. 3. Check the connections or try another electrical outlet. 4. Ensure that both units are turned on. 5. Make sure both units are on the same channel (A, B, or C). 6. Increase the volume level.
  • B
    bdiazSep 8, 2025
    How to fix static and interference in my Angelcare Security Sensor?
    • J
      joshua09Sep 9, 2025
      If you are experiencing static, distortion, or interference with your Angelcare Security Sensor, try the following: * Bring the Parents Unit closer to the Nursery Unit. * Ensure that both units are on the same channel (A, B, or C). * Make sure both units are turned on. * Rotate the Parents' Unit or move it away from potential sources of interference.

Summary

IMPORTANT ADVICE FOR INITIAL SETUP

Movement Alarm

Ensures the monitor alarms if no movement is detected.

Channel Selection

Sets the channel (A, B, or C) for both Parent and Nursery Units.

Cord Safety

Keeping cords away from baby and secured to prevent strangulation.

Voice-activated Sound Transmission

Monitor transmits sound when baby's sounds are detected; microphone sensitivity is adjustable.

WARNINGS

Battery Warning

Guidelines for using correct batteries, avoiding mixing types, and safe handling.

IMPORTANT SAFETY INSTRUCTIONS

Environmental and Placement Safety

Instructions on avoiding water, proper cleaning, ensuring ventilation, and avoiding heat sources.

Power Cord Protection

Ensuring power cords are routed safely to prevent pinching or walking over them.

Product Handling and Electrical Safety

Precautions for accessories, servicing, usage, power sources, and electrical safety.

IMPORTANT SAFETY INSTRUCTIONS RELATED TO USE OF BATTERIES

Battery Handling and Safety

Precautions for battery replacement, charging, disposal, and preventing leakage or explosion.

FCC AND IC REGULATIONS

RF Radiation Exposure Statement

Guidelines for maintaining compliance with FCC RF exposure limits.

Industry Canada Compliance

Statement confirming product meets applicable Industry Canada technical specifications.

SETUP REQUIREMENTS

Included Equipment

Lists components provided with the Angelcare monitor, like Parent Unit, Nursery Unit, Sensor Pad, and adapters.

Items to Prepare

Lists necessary items not included, such as hardboard and screwdriver.

Babys Room Setup

Placement instructions for the crib and Nursery Unit, emphasizing distance and stability.

STEP 1 - CHARGING THE PARENT UNIT

Battery Installation

Instructions for inserting rechargeable batteries into the Parent Unit.

Charging Procedure

Details on connecting the AC adapter and charging the unit for 15 hours before first use.

STEP 2 - INSTALLING THE SENSOR PAD

Strangulation Hazard Warning

Crucial safety warning about cord strangulation risk and precautions.

Nursery Unit Placement

Guidance on placing the Nursery Unit at least 1 meter away from the crib.

Cord Cover Securing

Instructions on using cord covers to secure the Sensor Pad cord along the crib leg.

Sensor Pad Placement

Steps for placing the Sensor Pad correctly on the hardboard at the center of the crib.

Floor Cord Cover Installation

Instructions for snapping together remaining cord covers that run along the floor.

Final Sensor Pad and Cord Check

Ensures the Sensor Pad is properly positioned and checks for cord slack.

Nursery Unit and Sensor Pad Connection

Placing the Nursery Unit at the correct distance and plugging in the Sensor Pad cord.

STEP 3 - SETTING UP THE NURSERY UNIT

Nursery Unit Battery Installation

Inserting alkaline batteries into the Nursery Unit for backup power.

Nursery Unit Placement and Connection

Positioning the Nursery Unit at least 1 meter away and connecting its AC adapter.

STEP 4 - TURNING ON YOUR MONITOR

Power On Procedure

Steps to slide the Parent Unit volume/power button and push the Nursery Unit power button.

Channel and Detection Mode Setup

Setting matching channels and selecting the desired detection mode (Sound & Movement, Tic OFF, Sound Only).

STEP 5 - TESTING YOUR MONITOR

Testing the Sensor Pad

Procedure to test the Sensor Pad's movement detection and alarm functionality.

Motion Alarm Troubleshooting

Guidance on what to do if the motion alarm does not sound.

ADJUSTING SENSITIVITY AND OUT-OF-RANGE

Adjusting Sensitivity Level

How to adjust the Nursery Unit's sensitivity dial for optimal movement detection.

Out-of-Range Function

Activating and stopping the Out-of-Range alarm to check unit communication.

SOUND AND NIGHT LIGHT FEATURES

Testing Sound Transmission

Procedure to check if the Nursery Unit is picking up sounds.

Adjusting Sound Level

How to adjust the volume on the Parent Unit.

Night Light Operation

Turning the Nursery Unit's night light on or off.

TROUBLESHOOTING COMMON ISSUES

Rechargeable Battery Care

Tips for maintaining battery life and performance.

False Alarms

Common causes and solutions for false alarms from the monitor.

Alarm Not Sounding

Troubleshooting steps when the monitor's alarm fails to activate.

LIMITED WARRANTY

TECHNICAL SPECIFICATIONS

Range, Channels, and Power Supply

Specifications for communication range, channels, and power requirements.

Regulatory Compliance

Information on FCC, IC, and environmental compliance for the product.

Angelcare AC601 Specifications

General IconGeneral
BrandAngelcare
ModelAC601
CategoryBaby Monitor
LanguageEnglish

Related product manuals