Why is the boiler temperature too high on my Animo ComBi 2017?
If the Animo Coffee Maker indicates 'BOILER TEMPERATURE TOO HIGH', it is likely due to a faulty boiler temperature sensor. Replace the temperature sensor and then press the X button to restart the machine.
Why is the boiler temperature too low on my Animo ComBi 2017 Coffee Maker?
If your Animo Coffee Maker displays 'BOILER TEMPERATURE TOO LOW', this is likely due to a fault in the boiler sensor. Replace the temperature sensor and press the X button to restart the machine.
What to do if my Animo Coffee Maker shows 'No water flow detected'?
If the Animo Coffee Maker shows 'NO WATER FLOW DETECTED', it indicates a fault in the water flow meter signal, meaning the flow meter impulses aren't reaching the main board. Check if the red LED blinks when the water inlet valve (lower LED K1) is activated. If there are no impulses, inspect or replace the flow meter and its connection cable.
What does it mean when my Animo ComBi 2017 says 'TEMP. SENSOR SHORT CIRCUITED'?
If your Animo Coffee Maker displays 'TEMP. SENSOR SHORT CIRCUITED', the temperature sensor is internally faulty. Replace the temperature sensor and press the X button to restart the machine.
What to do if the boiler filling time is too slow on my Animo Coffee Maker?
If the Animo Coffee Maker shows 'BOILER FILLING TIME TOO SLOW', it could be due to a problem with the mains water supply. Press the X button to restart the machine. Check the hose connection and ensure the tap is fully open. Alternatively, during the initial hot water boiler installation, the minimum level sensor might not have been reached within 120 seconds. In that case, check the inlet valve during operation and verify the upper LED (main PC board connector K1) lights up when the inlet valve is activated.
What causes a slow brew system filling in my Animo ComBi 2017?
If your Animo Coffee Maker displays 'BREW SYSTEM FILLING TOO SLOW', it could indicate a problem with the mains water supply. Press the X button to restart the machine, check the hose connection, and ensure the tap is fully open. Alternatively, during the initial installation, the minimum level sensor might not have been reached within 40 seconds. In this case, check the lower LED (main PC board connector K1). It must light up when the inlet valve is activated.
What does it mean when my Animo ComBi 2017 says 'DRY BOIL PROTECTION SWITCHED OFF'?
If the Animo Coffee Maker displays 'DRY BOIL PROTECTION SWITCHED OFF', it means the temperature protection of the brew system has been activated. Reset the temperature protection and descale the machine. Press the X button to restart the machine.
What does 'Brew System Min. Electrode Fault' mean on my Animo ComBi 2017 Coffee Maker and how do I fix it?
If your Animo Coffee Maker indicates a 'BREW SYSTEM MIN. ELECTRODE FAULT', it means the maximum level sensor detects enough water, but the minimum level sensor does not detect any water. Press the X button to restart the machine and check if the minimum electrode is working. You can also check if the level sensor signal reaches the electronic board by using the SERVICE MENU / 2.5 READ SENSOR VALUES / LEVEL SENSORS. It can also mean that the maximum level sensor falsely informs the electronic board that it detects a water level, so check if the cold water reservoir lid is contaminated with descaler solution, because the solution conducts extremely and causes false level information. Clean the complete lid under water or replace it.
What does 'Boiler Minimum Electrode Fault' mean on my Animo Coffee Maker?
If the Animo Coffee Maker displays 'BOILER MINIMUM ELECTRODE FAULT', it means the maximum level sensor detects enough water, but the minimum level sensor does not detect any water. Press the X button to restart the machine. Check if the minimum electrode is working. You can also check if the level sensor signal reaches the electronic board by using the SERVICE MENU / 2.5 READ SENSOR VALUES / LEVEL SENSORS.
What causes a 'False Water Flow Detected' error on my Animo ComBi 2017?
If your Animo Coffee Maker shows 'FALSE WATER FLOW DETECTED', it indicates a fault with the water inlet valve. Replace the inlet valve and press the X button to restart the machine.
General| Capacity per hour | 18 liters |
|---|---|
| Water connection | Yes |
| Voltage | 230V |
| Series | ComBi Series |
| Year | 2017 |
| Brand | Animo |
| Power | 2230W |
| Material | Stainless Steel |
| Product Type | Coffee Maker |
| Capacity | 1.8 liters per brewing |
To Next Page