What to do if my Animo OptiBean Coffee Maker displays 'E11 Ingredient motor error'?
If the Animo Coffee Maker shows 'E11 Ingredient motor error', it indicates that the ingredient motor(s) has stalled or its output is overloaded. Check the operation of the drive motors in the service menu 2.7 Hardware test. Empty the canister(s) and clean thoroughly. Switch the machine off and on again.
What to do if Animo Coffee Maker displays 'E25 fol w meter error'?
If your Animo Coffee Maker shows an 'E25 fol w meter error', it indicates that the inlet valve is open, but the flow meter isn't registering water flow. This could be due to low water pressure or an empty water tank (if it's a stand-alone setup). Check the water pressure, fully open the water supply tap, and inspect the connecting hose for kinks. Also, verify the operation of the inlet valve and flow meter. After checking these, switch the machine off and on again. If the error occurs after a specific recipe, check the dispensing valve function related to that recipe (DV1 brewer, DV2 mixer, DV4 hot water recipe) and replace it if needed.
Why does my Animo OptiBean show 'E6 Boiler temperature' error?
If your Animo Coffee Maker displays an 'E6 Boiler temperature' error, it means the temperature sensor is measuring a temperature over 105°C. First, check the water supply for air. Next, check the temperature sensor operation in the service menu 2.7 Hardware test. Finally, check whether the boil-dry protection was activated and reset it if necessary.
Why is my Animo OptiBean on 'Out of order Stand-by'?
The Animo Coffee Maker might be 'Out of order Stand-by' because it is on standby. This function can be set manually or automatically.
Why is my Animo OptiBean showing 'E21 boiler timeout'?
If your Animo Coffee Maker displays 'E21 boiler timeout', it means the heating element has been active for 6 minutes without the boiler reaching the required temperature. You can check the water supply for air. Also, check the boil-dry protection on the boiler, the log menu (if E6 boiler temperature, the boiler has boiled dry), the NTC sensor and wiring/connection and the SSR, and the heating element.
What causes 'E17 MDB error' on my Animo Coffee Maker?
If the Animo Coffee Maker displays 'E17 MDB error', it means there is no communication between the machine and the MDB payment system. Check the connection between the machine and the MDB payment system.
What does 'E18 Mixer group FET error' mean on Animo OptiBean?
If your Animo Coffee Maker displays an 'E18 Mixer group FET error', it means that the brewer or mixer motor output remains activated. The brewer or mixer motor output (FET) is defective and the control should be replaced.
What does 'E19 output FET error' mean on Animo OptiBean Coffee Maker?
If your Animo Coffee Maker displays an 'E19 output FET error', it means that the ingredient motor, valve, or fan output remains activated. The ingredient motor, valve, or fan output (FET) is defective and the control should be replaced.
What should I do if my Animo Coffee Maker shows 'E18 Mixer group FET error'?
If your Animo Coffee Maker displays 'E18 Mixer group FET error', it means the brewer or mixer motor output remains activated. The brewer or mixer motor output (FET) is defective and you should replace control.
What causes 'E8 Mixer 2 error' on Animo Coffee Maker?
If your Animo Coffee Maker displays an 'E8 Mixer 2 error', it means the mixer 2 motor has stalled, or its output is overloaded. Check whether mixer 2 is contaminated or incorrectly mounted. Clean it and check if the rotor turns freely. After checking these, switch the machine off and on again.
Essential safety information, warnings, and classification of safety signs for safe operation.
Details on the machine's intended purpose and warnings against unauthorized modifications or alterations.
Explanation of safety devices like door switches and temperature limits, plus general safety precautions.
Key safety advice during installation and a list of included accessories.
Steps for connecting the machine to the water supply, including filter system.
Guidance on correctly connecting the machine's power supply wires.
Important warnings and notes regarding safe machine operation and energy saving mode.
Steps for preparing cups, selecting recipes, and starting the dispensing process.
Procedure for dispensing beverages into jugs, including jug lock activation.
Schedules and procedures for daily, weekly, and monthly cleaning tasks.
List of error codes, their possible causes, and recommended correction steps.
Common display messages, their meanings, and required actions.
Troubleshooting common malfunctions like the machine not working or bad product taste.
General| Power Supply | Mains |
|---|---|
| Material | Stainless steel, plastic |
| Voltage | 220-240V |
| Drinks | Espresso, coffee, cappuccino, latte |
| Adjustable settings | Coffee strength, Temperature |
| Cleaning | Automatic cleaning |
To Next Page
