To Next Page
S
stevendavisSep 23, 2025
Why is my Animo OptiBean on 'Out of order Stand-by'?
- JjacobwoodSep 23, 2025
The Animo Coffee Maker might be 'Out of order Stand-by' because it is on standby. This function can be set manually or automatically.
Why is my Animo OptiBean on 'Out of order Stand-by'?
The Animo Coffee Maker might be 'Out of order Stand-by' because it is on standby. This function can be set manually or automatically.
What does 'Out of service E14 Output group error' mean on Animo OptiBean Coffee Maker?
If your Animo Coffee Maker displays an 'Out of service E14 Output group error', it indicates that either the ingredient motor output group or the valve output group is overloaded. If it's the ingredient motor, carry out the checks specified for error E11. If it's the valve output group, carry out the checks specified for error E10. Then, switch the machine off and on again.
What to do if Animo Coffee Maker displays 'E25 fol w meter error'?
If your Animo Coffee Maker shows an 'E25 fol w meter error', it indicates that the inlet valve is open, but the flow meter isn't registering water flow. This could be due to low water pressure or an empty water tank (if it's a stand-alone setup). Check the water pressure, fully open the water supply tap, and inspect the connecting hose for kinks. Also, verify the operation of the inlet valve and flow meter. After checking these, switch the machine off and on again. If the error occurs after a specific recipe, check the dispensing valve function related to that recipe (DV1 brewer, DV2 mixer, DV4 hot water recipe) and replace it if needed.
Why does my Animo OptiBean show 'E6 Boiler temperature' error?
If your Animo Coffee Maker displays an 'E6 Boiler temperature' error, it means the temperature sensor is measuring a temperature over 105°C. First, check the water supply for air. Next, check the temperature sensor operation in the service menu 2.7 Hardware test. Finally, check whether the boil-dry protection was activated and reset it if necessary.
What to do if Animo Coffee Maker displays 'E21 boiler timeout' error?
If your Animo Coffee Maker displays an 'E21 boiler timeout' error, it means the heating element has been active for 6 minutes without the boiler reaching the correct temperature. You should check the water supply for air and examine the boil-dry protection on the boiler. You may also want to check the log menu for an 'E6 boiler temperature' error, which indicates the boiler has boiled dry. In this case, check the NTC sensor, wiring/connection, and SSR. Finally, inspect the heating element.
How to troubleshoot Animo OptiBean 'E7 Brewer motor error'?
If your Animo Coffee Maker displays an 'E7 Brewer motor error', it means the brewer motor has stalled, or its output is overloaded. First, clean the brewer with the brush. Then, check the ground coffee volume (grams). After performing each of these checks, switch the machine off and on again.
What causes 'E5 Brewer error' on Animo Coffee Maker and how to fix it?
If your Animo Coffee Maker shows an 'E5 Brewer error', it means the brewer isn't running to the BREW position during the brewing process. Make sure the brewer is correctly positioned in the motor unit. Also, check brewer switch 1 and the brewer lever (right side) for correct operation using the service menu 2.7 Hardware test.
How to resolve Animo Coffee Maker 'E22 recipe timeout' error?
If your Animo Coffee Maker displays an 'E22 recipe timeout' error, it means the maximum preparation time (120 seconds) has been exceeded. Try switching the machine off and on again. Then, run the rinse and cleaning programs. If the issue persists, check the pump pressure (10 bar), ensure the coffee grind isn't too fine, and replace the brewer filters.
What should I do if my Animo Coffee Maker shows 'E11 Ingredient motor error'?
If your Animo Coffee Maker displays an 'E11 Ingredient motor error', it means the ingredient motor(s) have stalled or their output is overloaded. Check the operation of the drive motors in the service menu 2.7 Hardware test. Also, empty the canisters and clean them thoroughly. After these steps, switch the machine off and on again.
How do I fix 'E10 Valve error' on my Animo Coffee Maker?
If your Animo Coffee Maker displays an 'E10 Valve error', it indicates that the valve output(s) are overloaded. Check the valves and wiring for short circuits. Then, switch the machine off and on again.
Essential safety information, warnings, and classification of safety signs for safe operation.
Details on the machine's intended purpose and warnings against unauthorized modifications or alterations.
Explanation of safety devices like door switches and temperature limits, plus general safety precautions.
Key safety advice during installation and a list of included accessories.
Steps for connecting the machine to the water supply, including filter system.
Guidance on correctly connecting the machine's power supply wires.
Important warnings and notes regarding safe machine operation and energy saving mode.
Steps for preparing cups, selecting recipes, and starting the dispensing process.
Procedure for dispensing beverages into jugs, including jug lock activation.
Schedules and procedures for daily, weekly, and monthly cleaning tasks.
List of error codes, their possible causes, and recommended correction steps.
Common display messages, their meanings, and required actions.
Troubleshooting common malfunctions like the machine not working or bad product taste.
General| Power Supply | Mains |
|---|---|
| Material | Stainless steel, plastic |
| Voltage | 220-240V |
| Drinks | Espresso, coffee, cappuccino, latte |
| Adjustable settings | Coffee strength, Temperature |
| Cleaning | Automatic cleaning |
