Antunes VCT-35 - User Manual

Questions and Answers

B
Beth EricksonAug 20, 2025
How to troubleshoot no heat and conveyor belts not moving on my Antunes VCT-35?
- C
  Charles DavisAug 21, 2025
  If your Antunes Toaster shows no heat and the conveyor belts do not move, consider these potential causes: * The toaster might be installed incorrectly. Ensure you follow the installation and operating procedures. * There might be insufficient voltage, a defective power cord, or a defective rocker switch. Contact your Maintenance Person or Antunes Technical Service for service. * The hi-limit switch might have tripped open. Reset the hi-limit switch. * There could be a wiring problem. Contact your Maintenance Person or Antunes Technical Service for service.
J
Jennifer HoffmanAug 28, 2025
Why is the product under toasted on my Antunes VCT-35?
- N
  Nicole FowlerAug 29, 2025
  If the product is under-toasted, the platen heat is too low, or the drop time is too fast on your Antunes Toaster, it could be due to: * Insufficient voltage, a defective power cord, or a defective rocker switch. Contact your Maintenance Person or Antunes Technical Service for service. * A wiring problem. Contact your Maintenance Person or Antunes Technical Service for service. * An inoperative platen. Contact your Maintenance Person or Antunes Technical Service for service. * A conveyor drive motor that is inoperative or the incorrect conveyor motor installed in the toaster. Contact your Maintenance Person or Antunes Technical Service for service.
T
Taylor MatthewsSep 1, 2025
What causes no heat but conveyor belts moving in my Antunes VCT-35 Toaster?
- K
  Kim DouglasSep 1, 2025
  If your Antunes Toaster has no heat but the conveyor belts are moving, it could be due to: * A wiring problem. Contact your Maintenance Person or Antunes Technical Service for service. * An inoperative platen. Contact your Maintenance Person or Antunes Technical Service for service.
B
Brian AndersonSep 5, 2025
What to do if the product is getting stuck in my Antunes Toaster?
- P
  phillipramirezSep 5, 2025
  If the product is getting stuck or the conveyor belts stop when the product is toasting in your Antunes Toaster, consider the following: * Bun adjustment controls may be set incorrectly. Measure bun thickness and set bun adjustment controls correctly. * The conveyor release sheet may not be clean or is missing. Clean respective items.
J
Jody RamirezSep 9, 2025
Why do the crown and/or heel must be forced into my Antunes VCT-35?
- E
  ehunterSep 9, 2025
  If the crown and/or heel must be forced into your Antunes Toaster, it might be due to a heat shield that is improperly installed. Remove and reposition the heat shield. Ensure that buns are inserted with cut faces facing each other, with the heel in the front slot and the crown in the rear slot.
J
jose67Nov 12, 2025
Why is my product over-toasted in my Antunes Toaster?
- K
  klinNov 12, 2025
  If the product is over-toasted, the platen heat is too high, or the drop time is too slow on your Antunes Toaster, there are several potential causes: * The temperature might be set too high; try setting the temperature control to a lower setting. * The Bun Thickness Adjustment Control knobs might be set incorrectly; measure the bun thickness and set the bun adjustment controls correctly. * Buns might be sticking on the Release Sheet; clean or replace the Release Sheet or conveyor belt wrap. * The Conveyor Covers might not be installed; install the Conveyor Covers. * The Conveyor Belts chains might be installed incorrectly; reinstall Conveyor Belt. Other possible issues include a defective platen, defective or wrong drive motor, defective drive chain or loose sprocket, wiring p...
K
Kimberly HughesNov 16, 2025
What to do if the platen is hot but the conveyor belt chains are not rotating on my Antunes VCT-35?
- B
  bryan32Nov 16, 2025
  If the platen is hot but the conveyor belt chains are not rotating on your Antunes Toaster, possible causes include: * Incorrect installation. Ensure the toaster is installed correctly. * Wiring problems. Contact your Maintenance Person or Antunes Technical Service for service. * Inoperable or incorrect conveyor drive motor. Contact your Maintenance Person or Antunes Technical Service for service. * Broken drive chain or loose sprocket. Check the drive chain for kinks, broken or bent links, or other damage. Check the motor sprocket and drive sprockets (on drive shaft); tighten setscrew on flat of shaft if required. Check for damaged/worn sprockets and replace as required. * Heat Shield not installed or installed incorrectly. Install the Heat Shield so that it activates the Conve...
J
Jennifer ClarkNov 24, 2025
Why are the conveyor belts "jumping" or "snapping" on my Antunes Toaster?
- K
  Kristen CampbellNov 24, 2025
  If the conveyor belts are "jumping" or "snapping" on your Antunes Toaster, here are some possible causes and solutions: * The toaster may be installed incorrectly. Perform installation and operating procedures. * Bun adjustment controls may be set incorrectly. Measure bun thickness and set bun adjustment controls correctly. * Conveyor drive motor inoperative or incorrect conveyor motor installed on toaster. Contact your Maintenance Person or Antunes Technical Service for service. * Conveyor drive chain loose, worn or broken. Loose motor drive sprocket. Check drive chain for kinks, broken or bent links or other damage. Check motor sprocket and drive sprockets (on drive shaft); tighten setscrew on flat of shaft if required. Check for damaged/worn sprockets and replace as required. *...