ARCAIR N6000 Automatic System

Questions and Answers

D
Deborah BrownSep 9, 2025
Why doesn't the contactor air solenoid energize when the 'Start' button is pushed on my ARCAIR Industrial Electrical?
- S
  stephanie45Sep 9, 2025
  If the contactor air solenoid doesn't energize when the 'Start' button is pushed on your ARCAIR Industrial Electrical, there might be a break in the interconnect cable between the contactor and controller; check and replace it if necessary. A defective transformer in the contactor unit could also be the cause. Finally, the contactor unit may be in a high-temperature shutdown; allow it to cool and check the fan and filter.
H
Heather MejiaSep 8, 2025
Why does travel not begin after the arc is struck on my ARCAIR N6000 Automatic System?
- A
  Allison MorrisonSep 8, 2025
  If the ARCAIR Industrial Electrical system's travel doesn't begin after the arc is struck, ensure the “Travel” switch on the control panel is set to the “AUTO” position. A defective “Travel” switch on the control panel could also be the problem; replace it if necessary. Additionally, a defective “Travel Delay” potentiometer on the control panel, a defective carriage system, or a defective MCCB* might be the cause.
E
Edward MendozaSep 7, 2025
Why is there no power to the auxiliary outlet on my ARCAIR N6000 Automatic System tractor?
- C
  Chad MccannSep 7, 2025
  If there's no power to the auxiliary outlet on your ARCAIR Industrial Electrical tractor, check for power continuity from the source to the tractor. Also, inspect for a tripped breaker on the tractor and reset it if necessary. A loose connection on the outlet or a defective outlet could also be the cause; check the connections inside the enclosure and secure them, or replace the outlet if needed.
S
Sandra FranklinAug 22, 2025
Why does the start sequence trip the circuit breaker in my ARCAIR N6000 Automatic System?
- M
  Michael GreenAug 22, 2025
  If the circuit breaker trips during the start sequence of your ARCAIR Industrial Electrical unit, the issue might stem from a short in the interconnect cable linking the control panel to the contactor. Try repairing or replacing this cable. Another potential cause is a defective rectifier bridge in the contactor unit, which would also require replacement. Lastly, the breaker itself might be worn or defective, necessitating its replacement.
A
Allison BakerSep 4, 2025
What to do if the fan does not run with the control panel 'ON' on my ARCAIR N6000 Automatic System?
- A
  anthony44Sep 5, 2025
  If the ARCAIR Industrial Electrical system's fan doesn't run when the control panel is on, there might be a break in the interconnect cable linking the contactor to the controller; check and replace it if necessary. The fan itself could be defective and need replacement. Additionally, a defective transformer in the contactor might be the cause.
E
Edward CarsonSep 3, 2025
Why does the circuit breaker for the tractor keep tripping on my ARCAIR N6000 Automatic System Industrial Electrical?
- K
  Kevin JohnsonSep 3, 2025
  If the ARCAIR Industrial Electrical system's circuit breaker for the tractor keeps tripping, a defective motor speed control may be the cause, requiring replacement. The engagement of the drive gear to the track might be too tight; check and reset it properly. Debris lodged between the track teeth can also cause this; remove any debris. Other potential causes include a defective motor, a defective circuit breaker, an excessive load, or a defective transformer.
L
Laura ElliottSep 2, 2025
Why does the fuse for the carriage keep blowing on my ARCAIR Industrial Electrical?
- T
  thompsonwilliamSep 2, 2025
  If the ARCAIR Industrial Electrical system's fuse for the carriage keeps blowing, it could be due to a defective motor speed control, which would need replacement. Alternatively, the motor itself might be defective and require replacement. Finally, an excessive load could be causing the fuse to blow; try reducing the load.
L
Lauren LeachSep 1, 2025
Why doesn't the electrode feed at the start of the sequence on my ARCAIR N6000 Automatic System?
- J
  Joshua NelsonSep 1, 2025
  If the ARCAIR Industrial Electrical electrode doesn't feed at the start of the sequence, the “Arc Level” dial on the control panel may be set too high relative to the power supply's open circuit voltage. Also, the constant current (CC) or constant potential (CP) toggle switch on the MCCB* might be improperly set. A defective MCCB* can also cause this issue. Consider replacing the MCCB*.
W
William MooreAug 31, 2025
What to do if I cannot initiate a start sequence on my ARCAIR Industrial Electrical?
- J
  josephbanksAug 31, 2025
  If you cannot initiate a start sequence on your ARCAIR Industrial Electrical, the following could be the cause. Ensure the remote control pendant or jumper connector is properly connected to the receptacle. Check for breaks in the remote control pendant cable and repair or replace it. If the issue persists, the “Start/Stop” switch on the panel may be defective and need replacement. Finally, the MCCB* could be defective and need replacement.
T
tranjessicaAug 30, 2025
Why won't the carriage run when the switch is in the 'ON' position on my ARCAIR Industrial Electrical?
- J
  Joel JamesAug 30, 2025
  If the carriage won't run with the switch in the 'ON' position on your ARCAIR Industrial Electrical, first ensure the engagement lever is engaged. Next, check for power continuity from the source to the tractor. Also, inspect for a blown fuse and replace it if necessary. If these steps don't solve the problem, the power cable, power switch, motor, or motor speed control might be defective and require repair or replacement.

ARCAIR N6000 Automatic System Specifications

General

Brand	ARCAIR
Model	N6000 Automatic System
Category	Industrial Electrical
Language	English

ARCAIR N6000 Automatic System - User Manual

Table of Contents

Questions and Answers

ARCAIR N6000 Automatic System Specifications