Arcan A20018 - User Manual

To Next Page

1 02/07/2020

Model A20018

3 Ton Aluminum Floor Jack

For Technical Questions, Call: 1-800-879-7316

WARNING INFORMATION

This is the safety alert symbol. It is used to alert you

to potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible

injury or death.

WARNING: Indicates a hazardous situation

which, if not avoided, could result in death

or serious injury.

WARNING

IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING

BEFORE USING THIS DEVICE, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING

PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.

It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsibility

of the device owner to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels

are lost or not legible, contact

Arcan Customer Service for a free replacement. If the operator is not ﬂuent in English, the product and

safety instructions shall be read to and discussed with the operator in the operator’s native language by the purchaser/owner or his

designee, making sure that the operator comprehends its contents.

THE NATURE OF HAZARDOUS SITUATIONS

The use of portable automotive lifting devices is subject to certain hazards that cannot be prevented by mechanical means, but only

by the exercise of intelligence, care, and common sense. It is therefore essential to have owners and personnel involved in the use

and operation of equipment who are careful, competent, trained, and qualiﬁed in the safe operation of the equipment and its proper

use. Examples of hazards are dropping, tipping or slipping of loads caused primarily by improperly securing loads, overloading,

off–centered loads, use on other than hard level surfaces, and using equipment for a purpose for which it was not designed.

METHODS TO AVOID HAZARDOUS SITUATIONS

• Read, study, understand and follow all instructions before operating this device.

• Inspect the jack before each use. Do not use if damaged, altered, modiﬁed, in poor condition, leaking hydraulic ﬂuid or unstable

due to loose or missing components. Make corrections before using.

• Use only on a hard level surface capable of supporting load and free from obstructions so the jack is free

to reposition itself during lifting and lowering operations.

• Lift only on areas of the vehicle as speciﬁed by the vehicle manufacturer.

• User and bystanders must wear eye protection that meets ANSI Z87.1 and OSHA standards.

• Do not use jack beyond its rated capacity. Do not shock load.

• THIS IS A LIFTING DEVICE. Immediately after lifting, support the vehicle with jack stands

capable of sustaining the load before working on the vehicle.

• Center load on saddle. Be sure setup is stable before working on vehicle.

• Do not move or dolly the vehicle while on the jack.

• Do not use any materials that may serve as risers, spacers or extenders between the stock lifting

saddle and the load.

• Do not use any adaptors that replace the stock lifting saddle unless approved or supplied by the jack manufacturer.

• Always lower the jack slowly and carefully.

• Do not use (or modify) this product for any other purpose than that for which it was designed without consulting the manufacturer's

authorized representative.

• Failure to heed these warnings may result in fatal personal injury and/or property damage.

CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS

Failure to read this manual completely and thoroughly, understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS,

MAINTENANCE INSTRUCTIONS and not comply with them, and neglecting the METHODS TO AVOID HAZARDOUS SITUATIONS could

cause accidents resulting in serious or fatal personal injury and/or property damage.

WARNING

WARNING: This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer and birth defects or

other reproductive harm. For more information go to www.P65Warnings.ca.gov.

ASME PASE-2019

Main Page

Need help?

Do you have a question about the Arcan A20018 and is the answer not in the manual?

This document describes the Arcan Model A20018, a 3 Ton Aluminum Floor Jack, designed for lifting automotive loads.

Function Description:

The Arcan Model A20018 is a portable automotive lifting device intended for raising vehicles. It is crucial to understand that this jack is designed for lifting purposes only and not for sustaining a load. Once a vehicle is lifted, it must be immediately supported by jack stands capable of sustaining the load before any work is performed on the vehicle. The jack operates hydraulically, using a handle to pump fluid and raise the lift arm, which in turn lifts the saddle and the load. Lowering is achieved by slowly turning the handle counterclockwise to release the hydraulic pressure.

Important Technical Specifications:

Model: A20018
Capacity: 3 Tons
Minimum Lift Height: 3.78 inches
Maximum Lift Height: 18.90 inches
Handle Length: 47.64 inches
Product Length: 29.13 inches
Product Width: 13.00 inches
Product Height: 6.69 inches
Product Weight: 52.91 lbs.
Shipping Weight: 57.32 lbs.
Rear Caster Size: 1.97 x 1.2 inches
Front Wheel Size: 2.56 x 2 inches
Saddle Diameter: 4.57 inches The jack complies with ASME PASE-2019 standards, specifically regarding load sustaining tests, where it should not lower more than 1/8" (3.18mm) in the first minute, nor a total of .1875" (4.76mm) in 10 minutes. Lowering within this range is considered normal operation and not a warrantable defect.

Usage Features:

Safety First: Users are explicitly warned to read the entire manual, understand operating procedures, safety warnings, and maintenance requirements before use. The safety alert symbol (!) highlights potential personal injury hazards.
Pre-Operation Check: Before each use, the jack must be inspected for damage, alterations, poor condition, hydraulic fluid leaks, or unstable/loose/missing components. Any issues must be corrected before use.
Stable Operation Surface: The jack must be used only on a hard, level surface capable of supporting the load and free from obstructions, allowing the jack to reposition itself during lifting and lowering.
Proper Lifting Points: Lift only on areas of the vehicle specified by the vehicle manufacturer.
Eye Protection: Users and bystanders must wear eye protection that meets ANSI Z87.1 and OSHA standards.
Capacity Adherence: Do not use the jack beyond its rated capacity and avoid shock loading.
Immediate Support: After lifting, the vehicle must be immediately supported with jack stands capable of sustaining the load before any work is performed.
Load Centering: The load must be centered on the saddle to ensure stability.
No Movement: Do not move or dolly the vehicle while it is on the jack.
No Risers/Spacers: Do not use any materials as risers, spacers, or extenders between the lifting saddle and the load, unless approved or supplied by the manufacturer.
Controlled Lowering: Always lower the jack slowly and carefully.
Air Purging Procedure: If the jack exhibits symptoms of trapped air (partial pump stroke, inability to lift/sustain load, spongy pumping), a specific procedure involving pumping the jack against a load while slowly lowering it, and then repeating the process without a load, is outlined to purge air from the hydraulic system.
Handle Assembly: The handle consists of an upper and lower section, assembled by depressing a spring button. The assembled handle is then inserted into the handle yoke, ensuring engagement with the release valve u-joint, and secured with a set screw.
Fluid Type: Only hydraulic jack oil, a light turbine oil, Chevron Hydraulic Oil AW ISO 32, or Unocal Unax AW 150 should be used. Alcohol, hydraulic brake fluid, or transmission oil are strictly prohibited to prevent seal damage and jack failure.
Warning on Chemicals: The product may expose users to chemicals including nickel, known to cause cancer and birth defects or other reproductive harm in California.

Maintenance Features:

Visual Inspection: Before each use, a visual inspection is required to check for hydraulic fluid leaks, damaged, loose, or missing parts. Any abnormalities necessitate removal from service until repairs are made.
Storage: Store the jack in a well-protected, dry area, away from inclement weather, corrosive vapors, abrasive dust, or other harmful elements. All wheels should be on a relatively level surface.
Cleaning: The jack must be cleaned of water, snow, sand, grit, oil, grease, or other foreign matter before use. External surfaces can be cleaned with a mild soap solution, but avoid hydraulic components.
Lubrication (Monthly or as needed):
- Linkages and Pivot Points (#1): Lubricate with white lithium spray grease.
- Handle Receptacle and Handle End (#2): Remove the handle and lubricate with white lithium spray grease.
- Rear Casters and Front Wheels (#3): Lubricate bearings with white lithium spray grease.
Hardware Tightening: All accessible hardware should be tightened.
Fluid Level Check: Periodically check the hydraulic fluid level. It should be no higher than the top of the power unit's cylinder.
Label Maintenance: Keep all jack labels clean and readable.
Damage Check: Do not use the jack if any component is cracked, broken, bent, shows signs of damage, or leaks hydraulic fluid. Do not use if it has loose or missing hardware or components, or is modified in any way. Corrective action must be taken before further use.

The manufacturer provides a ONE-YEAR limited warranty covering defects in workmanship and materials, with specific exclusions for damage due to alteration, abuse, misuse, or unauthorized repairs.