EasyManua.ls Logo

Arcan ALFJ48 User Manual

Arcan ALFJ48
4 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
ALFJ48 and ALFJ60 1 09/04/19
Model ALFJ48 and ALFJ60
48" Farm Jack / 60" Farm Jack
For Technical Questions, Call: 1-800-879-7316
WARNING INFORMATION
This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING
BEFORE USING THIS DEVICE, READ THIS MANUAL AND THE LABELS ON THE JACK COMPLETELY AND THOROUGHLY UNDERSTAND ITS
OPERATING PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.
OWNER/USER RESPONSIBILITY
It is the responsibility of the owner to make sure all personnel intending to use this device to read this manual and the device labels prior
to use. It is also the responsibility of the device owner to keep this manual intact and in a convenient location for all to see and read. If the
manual or product labels are lost or not legible, contact the manufacturer for replacements. If the operator is not fluent in English, the product
and safety instructions shall be read to and discussed with the operator in the operator's native language by the purchaser/owner or his
designee, making sure that the operator comprehends its contents.
THE NATURE OF HAZARDOUS SITUATIONS
The use of this Farm Jack is subject to certain hazards that cannot be prevented by mechanical means, but only by the exercise of
intelligence, care, and common sense. It is therefore essential to have owners and personnel involved in the use and operation of the
equipment who are careful, competent, trained, and qualified in the safe operation of the equipment and its proper use. Examples of hazards
are dropping, tipping or slipping of loads caused primarily by improperly secured loads, overloading, off-centered loads, and using equipment
for a purpose for which it was not designed.
METHODS TO AVOID HAZARDOUS SITUATIONS
Failure to heed these markings may result in serious injury or death.
Inspect the jack before each use to make sure all hardware is included, secured, no damage to any components and is properly
lubricated.
Do not allow bystanders around the jack or under the load supported only by the jack.
Do not use jack beyond its rated capacity.
Support load with appropriate means immediately after lifting.
Always securely chock and stabilize the load to be lifted. Never place any part of the body under a raised load without properly
chocking and supporting the load.
Do not use the jack on any curved or tubular surface that will slip off the jack’s saddle.
When using the jack as a winch always use chains or tow straps that have a greater load capacity than the jack.
When using the jack as a winch do not exceed 5,000 lbs. of line pull or the top bracket will bend or break.
When using the jack for clamping, do not exceed 750 lbs. of force on the top bracket or it will bend or break.
Always keep your head away from the jack handle path of movement.
Before activating the reversing latch, always place the handle against the steel standard bar with the handle clip spring engaged
with the bar to prevent handle from moving up and down rapidly. Hold on to the jack handle so it is never in the horizontal
position when activating the reversing latch.
Never remove your hands from the jack’s handle when lifting or lowering a load.
When raising a vehicle’s tire off the ground never raise it more than 2” and only one tire at a time.
Never allow the jack to stand vertical and unsupported. Lay it on its side when not in use.
No alterations shall be made to this product.
The operation and safety of this jack depends on proper lubrication.
CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS
Failure to read this manual and jack labels completely and thoroughly and failure to understand its OPERATING INSTRUCTIONS, SAFETY
WARNINGS, MAINTENANCE INSTRUCTIONS and comply with them, and neglecting the METHODS TO AVOID HAZARDOUS SITUATIONS
could cause accidents resulting in serious or fatal personal injury and/or property damage.
The DANGER! safety symbol indicates a
hazard or unsafe practice that will result in
serious injury or death.
DANGER
DANGER
DANGER
DANGER
WARNING: This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Question and Answer IconNeed help?

Do you have a question about the Arcan ALFJ48 and is the answer not in the manual?

Arcan ALFJ48 Specifications

General IconGeneral
BrandArcan
ModelALFJ48
CategoryJacks
LanguageEnglish

Summary

Warning Information

Safety Alert Symbol

Explains the safety alert symbol for potential personal injury hazards.

Danger Safety Symbol

Explains the DANGER safety symbol indicating hazards resulting in serious injury or death.

Before Operating Instructions

Owner User Responsibility

Nature of Hazardous Situations

Methods to Avoid Hazardous Situations

General Safety Precautions

Key precautions for safe operation, inspection, and load handling.

Consequences of Not Avoiding Hazardous Situations

Pre-Use Inspection

Operating Instructions

Raising a Stationary Load

Step-by-step guide on how to raise a stationary load using the jack.

Lowering a Stationary Load

Step-by-step guide on how to lower a stationary load safely.

Clamping Operation

Instructions for using the jack for clamping applications, including force limits.

Winching Operation

Instructions for using the jack for winching, including strap requirements and force limits.

Maintenance Instructions

Cleaning the Jack

Guidance on cleaning the jack using solvents, air pressure, or brushes.

Lubrication for Optimal Performance

Details on lubricating the jack's components for smooth operation.

Specifications

Limited Warranty

Parts Drawing and Parts List

Related product manuals